These tests below only note my personal ESTIMATED ratings for the batteries I tested at the time I tested them. Any battery that is not a genuine Samsung, Sony, Murata, LG, Panasonic, Molicel, or Sanyo can change at any time! This can be one of the hazards of using “rewrapped” or batteries from other manufacturers so carefully research any battery you are considering using before purchasing.

Misusing or mishandling lithium-ion batteries can pose a SERIOUS RISK of property damage, personal injury, or even death. Never use them outside of a fully protected battery pack and you use them at your own risk. Never exceed the battery’s true continuous discharge rating (CDR), never let it get colder than 0°C or hotter than 60°C, and keep the plastic wrap and top insulating ring in perfect condition. Never use a battery that is physically damaged in any way.

Testing batteries at their limits is dangerous and should never be attempted by anyone who has not thoroughly studied the dangers involved, understands the risks, has the proper equipment, and takes all appropriate safety precautions.

If the battery has only one current rating number, or if it only says "max", then I have to assume the battery is rated at that current level for any type of discharge, including continuous.




Test Results
This cell performs a little better than the Molicel P28A, which is expected if it is indeed a P28B rewrap. I cannot guarantee that this cell is a Molicel P28B rewrap but due to its appearance, performance, and some other info I cannot discuss, in my opinion this is a rewrap of the Molicel P28B. That cell is the all-around best performing 18650 we can buy in my opinion.

The P28B is not yet in production so these would be sample “pre-production” cells sent to Molicel’s customers for testing and feedback.

This cell’s internal resistance is a bit lower than the P28A so it runs a few degrees cooler at high power levels. At 10A they performed the same in my testing. At 20A the Epoch ran for about 3% longer. At 30A the Epoch ran for about 8% longer.

The Epoch’s delivered an average of 2758mAh. This is well above the P28B’s 2650mAh minimum capacity rating but below the 2800mAh typical capacity rating. This might be due to these cells being pre-production P28B samples and not fully tweaked yet.

The 40A rating of these Epoch cells is not a true continuous rating IMO. The P28B is rated at 40A in the one-page spec sheet but that rating is temperature-limited to 80°C. When the cell gets that hot you must stop. Since the P28B would reach about 100°C at 40A you must stop about 2/3 of the way through the discharge.

So while, technically, the 40A rating for these cells is accurate I am disappointed that there is no mention on the wrap that it’s not a true continuous current rating (which can be used to compare against other cells). Most applications will never run this cell continuously at such high power levels but I believe strongly in accurate, consistently set ratings. 18650BatteryStore contacted me though and said that the wrap will be changed to add a continuous current rating and list the 40A rating as temperature-limited. This is great news!

Since the Epoch 28B reaches about 86°C at 30A (down to 2.5V) I am giving it an estimated 25A continuous and 40A temp-limited rating.

This cell is double-wrapped, a good thing for durability, but Molicels are already a little bit larger than most other cells. That can make this Epoch a tight fit in some devices. I recommend testing their size before committing to a large purchase if other cells are already a snug fit.


18650 Ratings and E-Scores Table:


20700/21700 Ratings and E-Scores Table:


Continuous Current Discharge Graphs



Ratings and Performance Specs Graphic


I want to work for the community full time! If you feel what I do is worth a couple dollars a month and you would like early access to battery availability, battery testing and news, and a say in what I test, then please consider becoming a patron and supporting my testing efforts: Battery Mooch | creating battery and device tests | Patreon.

To see how other cells have tested check out this link: Links To All 21700, 26650, 18350, 18500 Battery Tests

Once in a blue moon, ummm, blue momo, you have a dealio with a super wonderful person, and my transactionals with @bluemomo were just that! Thank you so very much for helping me free up some closet space!

Hi everyone. I'm a new member to the forum but not new to vaping. I've quit smoking cigarettes 10 years ago and have been making my own juice for 9 years. I make vanilla bean ice cream and menthol. My fav!!

Hello folks its been a long while but is there a thread still open for HotRod's EjuiceCalculator?

In any case, if anyone is interested, I have it working perfectly now under CrossOver on Mac Ventura.

The SXK PSYCHOMOD KBR-S Style Boro Mod is powered by Evolv DNA60 Chipset with variable wattage from 1W to 60W and powered by 1 x 18650 battery (not included). The Boro Box Mod is made by PA66 with 3D Printing and compatible with BB / Billet Boro Tank.
More info PSYCHOMOD KBR-S AIO Mod clone By SXK
3D Printing
Material: PA66 (Polyamide 66)
Powered by 1 x 18650 battery (not included)
Powered by Evolv DNA60 Chipset
Compatible with BB / Billet Boro Tank
Variable Wattage: 1~60W.

QUICK LINK,Click Here

DNA60W>>Buy SXK PSYCHOMOD KBR-S Style Boro Mod 60W Evolv DNA60 Chipset
70W >>Buy SXK PSYCHOMOD KBR-S Style Boro Mod 70W

So I recently bought this tank, ran some juice through it and cleaned it. Everything came apart just fine, except the afc ring and the base. Would anyone happen to know if the arc ring does come off of the base?

Vaptex Boxmo disposable vape is powered by a rechargeable 650mAh internal battery, featuring a 13ml vape juice capacity with 5% nicotine for up to 5000 puffs. The PEMT technology can deliver more flavorful vapor. Crafted perfectly to create an amazing blend of flavor by utilizing the 1.2ohm mesh coil, the patented AACT technology can help the disposable automatically heats and cleans e-juice.

Vaptex has been making massive in-roads in the vaping industry and has released quite a few disposable vape products over the last few years.Their latest, the BOXMO, is their largest boasting a 13ml pre-filled juice capacity.It is powered by a 650mAh battery that is rechargeable via USB-C and can deliver up to 5000 Puffs in total.

Vaptex has also introduced ‘Photo Etching Mesh Technology (PEMT)’ in the production of their mesh coils. This supposedly allows faster heat-up times through the more even and precise mesh.The Vaptex BOXMO comes with 50mg (5%) nicotine strength and is available in 10 different flavors.

More Details of Vaptex Boxmo:
Rechargeable 650mAh Internal Battery
13ml Vape Juice Capacity
5% Nicotine
5000 Puffs
1.2ohm Mesh Coil
AACT Technology
PEMT Technology
E-liquid Capacity: 13ml
Puffs: 5000
Nicotine: 5%(50mg)
Nicotine Type: nic salt
Battery Capacity: 650mAh
Charging: USB Type-C
Atomizing Core: 1.2ohm mesh
Firing Mechanism: Draw-activated



Recommended products:
novo 2c vape
voopoo vinci 3

The Rincoe Manto AIO Plus Kit 80W is an outstanding device that combines the convenience of a pod system with the power of a high-performance mod. This compact and stylish kit is built with advanced materials and cutting-edge technology, making it an excellent choice for vapers of all levels.

The Manto aio plus rincoe uk boasts an impressive output power range of 1-80W, and it can be powered by a single replaceable 18650 cell (not included). The device also features an input voltage range of 3.5-4.2V, and an efficiency of 95%, ensuring that it delivers consistent and reliable performance with every puff.

With a firing speed of 0.001s, the Manto AIO Plus Pod Kit is one of the fastest devices on the market. This lightning-fast response time allows you to enjoy instant vapour production, making for a smooth and satisfying vaping experience. The device also has a max output current of 30A, providing plenty of power for sub-ohm vaping.

The Manto AIO Plus Pod Kit is constructed using high-quality ABS, PC, and PCTG materials, making it both durable and lightweight. The device has a sleek and ergonomic design, with dimensions of 824728mm, making it comfortable to hold and easy to carry.

The kit includes a 3ml pod, which has a resistance range of 0.15ohm/0.3ohm, and is perfect for both direct-to-lung and mouth-to-lung vaping styles. The pod is easy to fill and features an adjustable airflow system, allowing you to customize your vaping experience to suit your preferences.

Rincoe Manto AIO Plus Pod Kit 80W is an excellent choice for vapers who want a compact and powerful device that delivers exceptional performance. Its fast firing speed, high output power, and adjustable airflow system make it a versatile device that can accommodate a wide range of vaping styles. Whether you're a seasoned vaper or just starting, the Manto AIO Plus Pod Kit is sure to impress. And you can enter vape warehouse to learn more.

You may like:
smok novo 5
crown m uk

The newly launched cutting-edge vaping device puff xtrax hhc stix 2g disposable vape kit is quickly gaining popularity among users for its ease of use and high-quality performance. This innovative product aims to provide an enhanced vaping experience through its advanced features and high-quality ingredients and is loved by a large number of vaping enthusiasts.

At the heart of the puff xtrax HHC stix 2g disposable vape kit is a powerful 550mAh battery that will give you a long-lasting vaping experience. And it comes pre-charged when you receive it, so it works right out of the box with no additional charging required. With a battery life that lasts for days, you can enjoy an uninterrupted vaping experience without worrying about running out of power.

2ml of e-liquid capacity, filled with high-quality e-liquid without harmful chemicals and additives, with high-quality HHC (tetrahydrocannabinol) content, each drop has been carefully developed to restore the purest taste and flavour of e-liquid mouthfeel so you can enjoy your favourite flavours for a long time. HHC has high potency levels to provide a more effective and longer-lasting vaping experience than regular CBD oil. This makes the puff xtrax hhc stix 2g disposable vape kit ideal for users looking for a more intense vaping experience.

The entire device is made of top-grade materials, which are not only durable but also safe and secure, providing you with a satisfying and safe vaping experience. This ensures that you can enjoy your vaping experience without any health risks or negative effects on your body. It has an advanced heating element inside to ensure that your e-liquid heats up evenly and quickly. This results in a smooth and consistent vaping experience without any harsh or burnt taste, allowing you to enjoy the ultimate in vaping.

This powerful and innovative vaping device can bring you an enhanced and unforgettable vaping experience. With its advanced features and high-quality HHC ingredients, it will definitely open up new horizons for your vaping experience.

More attractive new products are in our vape online store, you are welcome to choose.

We also want to recommend more boutiques for you:
buy elf bars online
10000 puffs vape

Product: VAPORESSO GEN 200

The SMOK Novo 5 Kit, 900mAh Is geared towards MTL vapers supporting 0.5ohm-2.5ohm resistance and have a Plug-n-play coil installation. The Novo 5 is available for both freebase e-liquid and nic salt E-liquid. The coil has an anti-leakage structure to make every drop fully used and prevents a messy vaping experience.



Features:
1. Top-fill Design
2. Button/Air Switch
3. Air-inlet Ring
4. novo 5 Meshed 0.7ohm MTL Pod
5. Variable Wattage 5W-30W
6. 900mAh Built-in Battery
...

Click here for more:

SMOK Novo 5 Kit: SMOK Novo 5 Pod System Kit

Black timesvape heavy hitter mech mod 21700 $40 plus shipping lightly used. Will throw in Samsung 30t I used for like 2 weeks for 5 bucks or 2 for 10 bucks. There both lightly used I bought them for this mod about a month ago. The same time I bought the mod.

Explore Our Brands:​

• Smok
• Geekvape
• Vaporesso
• Voopoo
• Jam Monster
• Uwell
• Air Factory
• Humble Juice Co.
• Candy King and more

Quick to ship , communicates well, A+

Great buyer, great communication, and quick payment. Would do business with again. Thanks @bsidb

Hi, today let's have a look at the Tank Steam Crave Meson RTA sent to me by @sourcemore online shop. In this Test I will examine each of the characteristics that distinguish this item. I hope that at the end of this reading you can understand this product, and therefore decide whether to invest in it or not. As always, my opinions are free and based on my personal experience.
• Enjoy the reading.

► Steam Crave Meson RTA; Before starting, let's see together some special features indicated by the manufacturer:
• 1. Single coil RTA for restricted airflow
• 2. The honeycomb airflow hits the coil directly
• 3. Ideal airflow for powers between 20 and 50W
• 4. Adjustable top airflow, no leakage
• 5. Single coil deck, easy to build and wick
• 6. 5ml/6ml capacity
• 7. Wide Drip Tip 810
• 8. Perfect match with Hadron Lite Box Mod and Hadron Mini Box Mod



► Steam Crave Meson RTA; Packaging:
The matte black package reports on the front; the logo and the name of the manufacturer which are highlighted in red, the stylized image of the Tank and the black writing on a red background "The Best Single Coil RTA!".

On the back of the box are reported; the scratch & check, a barcode, logos and legal trademarks. While on the remaining sides we find various indications, among which; the color of the sample contained in the package, the address of Steamcrave and the numerical code "SC214".





► Steam Crave Meson RTA; Packing List:
• 1* Meson RTA
• 1* 6ml convex glass
• 1* Bag with O-rings and screws
• 1* Allen key
• 1* Steam Crave Sticker
• 1* User Manual



► Steam Crave Meson RTA; Specifications:
• Material: Stainless steel
• Diameter: 25mm
• Deck: Postless Single coil
• Airflow: Top adjustable
• Filling system: Top threaded
• Capacity: 5/6ml
• Drip Tips: 810
• Contact pin: Gold plated



► Steam Crave Meson RTA; Available colours:
• Stainless Steel
• Gunmetal
• Black



► Steam Crave Meson RTA; First Impressions:
Steam Crave is a well-known brand among passionate vapers, thanks above all to the numerous editions of the famous Aromamizer vaporizers. Steam Crave is a registered trademark in US and EU, its devices are designed by international engineering team and are made by Chinese ecig manufacturer Beautiful Technology Group Co., Ltd, which has 11 years experience in this sector. I have enjoyed several devices from Steam Crave and I must say that most of them are uncompromisingly crafted for the best vaping experience while offering affordable products of the highest quality. When I received Meson RTA I immediately thought of placing it on the SBS Hadron Lite Mod and I must say that I got a perfect match. Thanks to the reduced diameter of 25mm you can therefore install Meson RTA on some SBS Mods such as the Hadron but also like the Brunhilde by Vapefly. Using the convex glass present in the kit you will not be able to use these SBS Mods but you will have to install Meson RTA on a traditional type Mod; in this case a dual battery Mod could really be for you.





Starting to handle Meson RTA you immediately realize that this is a quality vaporizer, with an attractive appearance, nice engravings, good finishes and with a solid structure. The 810 drip-tip is held energetically in the top cap by an internal oring, to extract the cap you have to unscrew it a few turns counterclockwise, then through two huge slots you can introduce 5 or 6ml of e-liquid into the tank, depending on the glass which you decide to use.



So the top cap and the bottom base are the parts that can be quickly separated from the tank. To replace the glass, insert a simple 2 cent coin into the upper notch of the fireplace and extract the air control system. Furthermore, you can continue to separate the various elements of Meson RTA (there are many pieces) but in the end your washing and cleaning operations will be really effective and you will easily reach every smallest detail.





Now I will briefly try to explain to you how the air control system works and how it is done. The AFC regulation takes place via a ring which regulates the opening of two opposing slots. The airflow descends from top to bottom and then spreads inside the bell thanks to a honeycomb structure that uses a total of 18 optimally directed holes on the coil to obtain a wide coverage for a greater aromatic yield. Subsequently the steam goes up through the chimney.



The honeycomb structure can be separated from the chimney, in the image below you can easily guess its final position right above the deck and coil.



Meson RTA uses a postless deck that can be disassembled through two cross screws. The deck is a good size for the correct installation of a single 2.5/3mm diameter coil, the only caveat is that you have to cut the coil legs to a pre-established length before inserting them into the holes. To install the resistance you will need to use the orange toolkit and unscrew the small lateral Allen screws. Then you will have to insert the legs of the coil into the appropriate holes and tighten the screws.





The cotton must be inserted into the slots without pressing it too much, just place it in the tanks to obtain a smooth and regular feed. I used the lines marked with the letter "A" to show you the cotton placed in the draw slots and its remainder inside them (visible) in the lower part of the deck. You can also see two lines marked with the letter "B"; this is to show you how the deck should fit into the bell; you have to match the two metal tabs of the deck with the two respective housings in the bell.



The caseback is knurled on the surface and inside it contains a thread to allow you to screw it solidly to the Tank. Inside the bottom you can see a large oring on the perimeter, while in the center of the through hole there is another oring to make the Meson RTA airtight. The 510 Thread has a sliding thread like the others and the Pin can be adjusted, also the Pin is finely gold plated for better electrical conductivity.



► Steam Crave Meson RTA; Vaping Test & Final Conclusions:
Steam Crave recommends using a resistance with an internal diameter of 2.5mm for a power range between 20 and 50W, I found in my hands a preassembled coil of a complex type and of unknown material, with a diameter of 3mm, I decided to try it. With the resistor I used I found a resistive value of 0.37Ω. The liquid I chose for this test was TOB Hypnos diluted 10% in a 50:50 VG/PG base with 3mg/ml of boost. The coil installation operations were not complex at all and the cotton arrangement was simple and intuitive, the build immediately provided a good supply of e-liquid to the coil. With a selected power of 30W and with AFC wide open I obtained a fairly wide air flow, lots of dense vapor with a good flavor, by slightly closing the air slots the vapor takes on a warmer tone, the hit in the throat increases and the flavor becomes tastier and more concentrated. I also appreciated the fact that the tank does not get hot and the puffs are silent, evidently the noise is effectively soundproofed by the robust steel structure of the Meson RTA. I really liked the kind of "airiness" you get with the Meson, in this test I used an "intermediate" coil for 30W of power, but I really think that also with other types of coils suitable for lower or higher powers it is possible to obtain equally valid results thanks to this excellent type of air ducting. The finishes and assembly of the Meson RTA are really nice and precise, the only precaution is that you have to make sure you tighten the chimney well using a coin, tighten hard and you will not have any loosening of pieces during the adjustment operations air and tank filling. I would have preferred the presence of some cotton laces and some coils, however in the kit there are a convex glass and numerous spare orings, so as far as the equipment is concerned, you can turn a blind eye also considering the excellent aromatic yield of Meson RTA which also guarantees the complete absence of liquid leaks.

• Steam Crave Meson RTA can be purchased for the affordable price of $31.59 on Sourcemore using this link:

• Thank you for reading.

I've been mixing my own juice for about 4 years. I've tried a lot of different flavorings. Similar to a peachy flavored vape juice I ordered once from humble, the Flavor West Orange Natural flavoring seems to have an odd effect on me. It makes me tired, light headed, and gives me a headache. I've tried smaller amounts, but to no difference. After about a month of testing with it on and off, I have narrowed it down to just this particular flavoring. Really awful feeling.

I potentially have a bad batch. Perhaps I am just allergic to it or something. I do recall it having particulate floating around when I first got it, but it went away and I ignored it, not wanting to waste it. Generally though, I would recommend that it be avoided. There are plenty of other orange flavorings out there and I would not risk this awful experience.

The long-awaited President's Day event is here! Get ready to enjoy amazing promotions, incredible deals, and discounts on our website!

Event time:
Feb. 16th 00:00:00 - Feb. 22nd 23:59:59 (US time)

Event format:
We will provide a 12% discount for all products across the entire site. Don't miss this opportunity to save big and shop to your heart's content. Use the discount code "PRED" at checkout to enjoy the discount.
For our customers in the US, we also offer free shipping for all orders over $85 from our usa warehouse after applying the discount.

Now is the perfect time to stock up on your favourite products or try something new.

Be sure to mark your calendars and take advantage of these limited-time offers before they expire. Shop now and enjoy a hassle-free online shopping experience on the best online vape store. Happy President's Day!

We sincerely recommend to you:
elfbar online
dessert flavors e liquid 2023

Discover Honeyroot Extrax HHC Live Resin Disposable 2G, featuring a 2g capacity, mixed cannabinoids, and is carefully made using live resin processes. Holding up to 2g or 2000mg, the Delta Extrax x Honeyroot Disposables contain live resin cannabinoids harvested from legal hemp plants under the 2018 Farm Bill. Featuring HHC, HHC-O, and HHC-P, this blend of potent cannabinoids in a disposable vape device is perfect for those that are constantly on-the-go.

More Details of Honeyroot Extrax Disposable:
Capacity: 2g (2000mg)
Battery: 280mAh
Cannabinoid: HHC, HHC-O, HHC-P
Concentrate: Live Resin
< 0.3% Delta-9 THC
Firing: Draw-Activated
LED Battery Life Indicator Light
3rd Party Lab Tested
Charging Port: MicroUSB

Flavors:
Banana Kush (Indica)
Super Sour Diesel (Sativa)
Thin Mint OG (Hybrid)
Strawberry Cough (Sativa)
Green Crack (Sativa)
Blue Dream (Hybrid)



Recommended products:
dessert flavored vape juice
fruits flavor e juice

For many friends who are looking for an electronic cigarette with a large capacity, small size and stylish personality, r and m has always been a good choice. This r and m bar disposable kit has an absolute advantage in the same series of products. As you can see, it has an ingenious appearance, with a smart and compact body in a variety of bright colours. The upper part of the fuselage has a diamond-like cutting process, which is extremely shining. The cigarette holder has smooth lines, and the style is in harmony with the fuselage, which is very beautiful.

As a disposable vape kit, it is very small and cute, and you can easily carry it with you wherever you go. Whether you're travelling, working or on the go, this set is the perfect companion for your vaping needs. And you don't have to worry about maintaining it or replacing parts, just use it until it runs out of e-liquid, then dispose of it responsibly.

The battery life of the R and m bar disposable vape kit is impressive. With a 900mAh battery capacity, the device can go for days without recharging. This means you can enjoy your vaping experience without constantly looking for a power source. Not only that, you don't need to worry about any buttons or settings, just inhale to activate the device and enjoy a smooth and satisfying vape. The device is also suction-activated, meaning it only triggers when you take a puff, making it a safe and user-friendly option.

Whether you prefer fruity-sweet flavours or rich and decadent flavours, there's something for you. The 15ml e-liquid capacity also means you can enjoy your favourite flavours for longer, being able to provide you with up to 9000puffs of enjoyment without having to constantly refill the device.

In addition to its impressive features, the R and M Bar Vape Disposable Kit is also affordable and convenient. You can buy this kit for a fraction of the price of traditional vape equipment, and you don't have to worry about maintenance or care. This device is the perfect solution for anyone looking for an easy vaping experience. Try it now and experience ultimate convenience and satisfaction!

More new products are available in vapes for sale near me, you are welcome to choose.

You might also like：
clearance vape
flum float flavors

The Proxy is a first-of-a-kind modular Vaporizer Vape that is compatible with any type of extract such as wax, dabs, shatter, or crumble.

The Proxy features Puffcos advanced 3D ceramic coil, which, if you look closely, you will be able to see the heating wire embedded into the walls of the coils.Unlike traditional coils, which get their heat only from the bottom, the heat here comes from all directions.

This heating system, coupled with precise temp control, prevents the extract from boiling off before you actually draw. This system creates consistent, predictable results.

Unlike a vape pen, Puffco Proxy Vaporizer has a large mouthpiece that allows the vapor to cool down before inhaling it.Heat rises, and the design of the Proxy allows the excess heat to dissipate into the air instead of into the mouthpiece or into your face.Traditional pipes have been taking advantage of this design for a long time. It’s been time-tested and proven to work. Puffco didn’t invent the wheel here. They just modernized it.



Recommended products:
best ejuice
tobacco flavored vape juice

I was ready to start building - have a regulated squonker and appropriate atomizer coming in the mail. But last night the pod on my silly Geekvape H45 went kaput and dumped juice all over everything, and I was FED THE EFF UP! Cue going to the best B&M in my hometown this morning and picking up a little mod and the Dead Rabbit v2 RDA.

My first build (ever) are 2 simple, okayish spaced Ni80 coils ringing in at 0.3 ohms together. Wicked em badly (I think) with some of the rayon Kat sent me, tried to follow the advice from previous threads, but it's my first time, y'know?

Bruh!!! It works!!! It's a pretty decent vape, tastes good, and I really think I owe it all to the trooper that rayon is - it's been really forgiving of my crappy skills as a virgin. <3

The rayonatti were right about everything! I'm never going back to stock coils!!

Orange County CBD & CBG Disposable Vape Kit is a cutting-edge product that combines the therapeutic benefits of both CBD and CBG in a convenient and easy-to-use vape kit. This disposable vape kit contains 1000mg of high-quality CBD and CBG distillate, providing users with a potent and effective dose of these cannabinoids.

Orange County CBD Vape is a reputable brand that prides itself on producing top-quality CBD products that are rigorously tested for purity and potency. The brand has a wide range of products that cater to different needs and preferences, including oils, gummies, capsules, and topicals.

CBG, short for cannabigerol, is a lesser-known cannabinoid that is gaining popularity due to its potential health benefits. CBG is often referred to as the "mother cannabinoid" as it is the precursor to other cannabinoids such as THC and CBD. CBG is known for its potential anti-inflammatory, analgesic, and antibacterial properties, making it a promising alternative to traditional medications.

When CBD and CBG are combined, they work synergistically to enhance each other's therapeutic effects. This is known as the "entourage effect," which suggests that cannabinoids work better together than they do individually. By using a vape kit that contains both CBD and CBG, users can potentially experience a more significant and comprehensive range of benefits.

The Orange County CBD & CBG Disposable Vape is perfect for those who want to experience the benefits of CBD and CBG quickly and easily. It is a great choice for both experienced vapers and those new to the world of CBD and CBG. And with vape shops uk online cheap, you can get more products for your money.

I would like to show you:
vinci 3
disposable vape 5000 puffs

Innokin Klypse Pod Kit

Klypse Pod Kit features no buttons and no settings design. It is powered by a built-in 700mAh battery with 16W output and Type-C fast charging for less charging time and all-day vaping fun. It is equipped with a 2ml pod cartridge that features 0.8Ω mesh coil and easy side filling system. With magnetic cap, it can protect the mouthpiece from dust to keep clean in a way. It is also made of aluminium alloy material and has ultra compact size & elegant appearance.

Details:
1. Built-in 700mAh battery
2. Type-C USB charging
3. 2ml capacity, side fill
4. 0.8Ω mesh pod cartridge
5. MTL vaping experience
6. No buttons and settings design
7. Magnetic cap to keep clean
8. Aluminium alloy material
9. Ultra light and compact




BP MODS Tomahawk SBS Squonker Mod

Tomahawk SBS Squonk Mod is a box mod that has 5-60W power range, features side-by-side and squonker designs. It is powered by 18650 battery, made by the material of aluminum alloy + SS304. BP MODS Tomahawk Mod is compatible with RTAS (diameter≤24mm, height≥33mm), RDAS (diameter≤24mm). It also supports Bypass/Power/Boost/TC mode.

Details:
1. System: NIFE30/NIFE48/SS/TI/NI/BYPASS
2. 100-315℃/200-600 adjustable temperature
3. Adjustable power, resample resistance
4. Compatible with RTAS (diameter≤24mm, height≥33mm)
5. Compatible with RDAS (diameter≤24mm)