75W Vaporesso TARGET 2 VTC Kit with Ceramic cCELL Coil

Status
Not open for further replies.

Fearlessleader

Senior Member
ECF Veteran
Verified Member
Sep 11, 2014
296
179
63
Portland TN USA
No warranty. Had it 3 months. I let it set overnight. I put in a battery today and it started working again. I don't charge in mod. Would be nice to have a reset. Thanks

I glad it came back for you but I would not start dancing yet! When any type of electric device stop working and starts again most time that means that something is failing it's not just having a bad hair day the thermal protection for the board should not take more than 5 min to reset. Most of my PVD's I seen reset after some chain vaping in a matter of few seconds I would still give it a good going over. If it out of warranty try to find something YouTube and check to see that no ejuice has got inside and if it has I clean it really good with alcohol and use the good stuff as pure as you find 80% to 90% as you don't want to get water anywhere near the inside of the unit.

Now as far as charging. I charge a lot of my single 1865 mod with the onboard charger they work well enough but even on those I like to run them till the device says it's low and then charge them in a real charger twice a week.
For my mods that have 2 or more batts I do the same, but I note the voltage when they go in the charger if they come out uneven by more than .2v to .3v I will charge them every other day for a week and see if the discharge state gets closer, if it does then I only use the onboard charger with the onboard charger when I am on the fly and but when I get home then I put them back in the charger.

I have a few units that have never seen anything but there onboard charger like my Vapor Flask those screw in type battery covers all my box mod I make myself so the battery door is magnetic.
But I would make sure to check all you PVD's after the warranty is up for juice swapage Sometimes you will get up in the morning and for whatever reason at tank leaked or your dripper wept all over your stuff till the warranty is up you can't really open the unit up as in a lot of units have a seal and they can see if you been in there and if you have well your SOL Big Time!
 
  • Like
Reactions: SS stingray

GemInEye

Super Member
ECF Veteran
Verified Member
Jun 1, 2015
700
2,769
Somewhere In PA
Why in the world is my gemini leaking? I just got it yesterday. I have the ss 06 in there broke it in really gentle... Let the tank sit all night half full. Picked it up this afternoon... Juice everywhere! Pouring out of the airflow. Everything was really tight on it so it wasn't my base or coil being lose.. Anyone else have this issue?

Also i saw someone mentioned wishing there was a reset on the target.. There is i know if involves taking out the battery and holding buttons down.. Which ones? You will have to Google cause I've forgotten.. It does work i had to do it.

Tapayappin
 

iMove2016

New Member
May 23, 2016
1
0
49
I just tried the new .6 ohm SS Ccell coil today. Immediately began dry hitting at 40W even after being primed and let soaking for about 5 min. It says that it can accommodate 75W. After about 2 hours of use and about 7 dry hits I go up to my local vape shop to try another coil. The guy behind the counter suggested that I prime it more and showed me how they suggest to do it. He literally fills the entire coil with juice until its overflowing and makes a huge mess. After its cleaned up he told me to refill the tank and let it sit for 30 min. So after all of that I get a burnt taste at any wattage over 40W. The nickel temp control coils have been working great and have been long lasting, but I'm really disappointed in the .6 ohm SS coils so far. Has anyone else tried them and had a better experience?
 

GemInEye

Super Member
ECF Veteran
Verified Member
Jun 1, 2015
700
2,769
Somewhere In PA
I just tried the new .6 ohm SS Ccell coil today. Immediately began dry hitting at 40W even after being primed and let soaking for about 5 min. It says that it can accommodate 75W. After about 2 hours of use and about 7 dry hits I go up to my local vape shop to try another coil. The guy behind the counter suggested that I prime it more and showed me how they suggest to do it. He literally fills the entire coil with juice until its overflowing and makes a huge mess. After its cleaned up he told me to refill the tank and let it sit for 30 min. So after all of that I get a burnt taste at any wattage over 40W. The nickel temp control coils have been working great and have been long lasting, but I'm really disappointed in the .6 ohm SS coils so far. Has anyone else tried them and had a better experience?
Aside from my tank leaking the coil. 6 has been great but im not at 40w. Im at 20w to 25w and satisfied with that. I did get dry hit in the beginning but i take pulls with it closed the whole ways up and without firing then let it sit. I then slowly work ccells up to the wattage . I start lower than the recommendation and take my time. As far as priming i put just a few drops down the center and that's it. I don't like messes. I do this with ccell kanthal and ss. The coils have been awesome.. I just baby them for the first tank . . Hope this helps.

Tapayappin
 
  • Like
Reactions: cooladdict

Junglegeorge

Senior Member
ECF Veteran
Verified Member
Dec 10, 2011
128
184
63
Sweden
www.jgg.se
After receiving a new order of 0.9 Kanthal coils from Heavengifts.com I haven't had any dryhit/airlock problems. Still some occasional leaking through the airholes but not that bad. I do think I prefer the original Target tanks before the Gemini but the topfill on the Gemini is nice. Could do without the top airflow though.
 
  • Like
Reactions: cooladdict

cooladdict

Vaping Master
ECF Veteran
Verified Member
Apr 28, 2012
7,735
49,856
58
Seahawk Nation
After receiving a new order of 0.9 Kanthal coils from Heavengifts.com I haven't had any dryhit/airlock problems. Still some occasional leaking through the airholes but not that bad. I do think I prefer the original Target tanks before the Gemini but the topfill on the Gemini is nice. Could do without the top airflow though.
Yay, the bad batch is gone!! I still have an unopened back of the kanthals so I don't know if they are part of that batch or not, but the SS coil that came installed in the Gemini is outstanding, so I figured they had solved whatever issue they had with that one batch of coils. I agree about the top airflow on the Gemini. I don't use it, either. The Gemini never even gets warm so it serves no purpose for me and I get the perfect vape with the bottom air flow wide open.
 

Fearlessleader

Senior Member
ECF Veteran
Verified Member
Sep 11, 2014
296
179
63
Portland TN USA
Hi, I have the first release of the vaporesso 75-watt kit And I am not sure what is the target the tank or the PVD but anyway, I had the since around Christmas and I have seen a deal last week and picked up a 5 pack of the Ccells. I was thinking that I should change it out I must vaped 200ml of juice by now thru it. Now I will say this as well I only use juice from Metrovapors and truthfully I think their juice is the cleanest juice on the market. and I tried so many juices even the so called Premium juice which most of those got more junk in them so I long stopped buying any premium juice right now I get my juice from only 2 places Wild vapor and Metro. I use wild vape for finding flavors to try and it cheap and from Metrovapors, I have their full line of Cloud Chasers Line but that is really 2 juice lines now that just come down to if the juice is 90/10 VG/PG or 80/20 the call the new 80/20 flavor Chasers. So I keep that whole line in stock so so I can go from 1 crazy 120 sales to the next on sale that line cost me anywhere from 9.99 to 14.99 but it half price at the worst to 66 % off as full price is 30$
so sorry to get off topic but I think it has a lot to do with the how long the coil lasted 2 things I hate buying is juice and batteries PVD's and Atty's that's fun to buy the batts suck because there is so much BS out there with fakes and stuff even sony got to be a rip off the last batch VTC5 are only 20amp constant so that only leaves you with VTC 3"s or 4'S if you want 30 amp batts it just not fun when I shop for batts it takes the whole weekend.
So now back to our regular scheduled program So after 6 months and 200 + ml of juice my Nickle .2 ohm Ccell get changed out and nothing seems to have changed it might taste a tiny bit cleaner but the vapor was right on the spot. Now I have swapped it around to few of my other PVD's right now it's on my Evic VT at 40 watts and 410 f and it vaping great and I have the Smok Gimlit with the .2ohm nickel coils in it and even that coil is 2 moths old but I would not think I put more than 60ml of just thru that But I got a deal last week on coils for that and paid like 16$ for 15 of those it was like buy 2 at 8$ and get 1 free I have a few other tanks that use coils but most that I have RBA in them all. and I have to say that I only need to replace the Japanese cotton out in them every 3 weeks.

So I bet you were wondering where I was going with the juice thing before. I betting it has a lot to do with coil and cotton life. Now I remember buying Fight your Fate by kings crown and mothers milk by suicide bunny that was some of the worst juice I ever tasted. One crack our plastic tanks. and the other even corroded the inside of my wife's Erlkonigin where she would not use the tank anymore. She gave the bad tank to me and I cleaned the whole thing with acetone and since it cracked the plastic tank I just use it with the metal one. Now PVD problems are totally different but, tank's, Atty's, coils, cotton,and even o-rings. I seen damaged by bad juice and it's not a pretty thing.
 

WickedWicks

Super Member
ECF Veteran
Jan 13, 2015
355
466
This sounds interesting to me as a mtl-vaper, especially the coil
"CCELL-GD MTL 1.4Ω"
Guardian Tank
You can see it here:

Vapin' Heathen | youtube.com

Unfortunately it's not a classic ccell head but one of these gurgly cup-style heads. Also it seems you have to use this proprietary drip tip. An absolute no go. Couldn't they just make an ordinary ccell MTL head!!!?
 
Last edited:

Junglegeorge

Senior Member
ECF Veteran
Verified Member
Dec 10, 2011
128
184
63
Sweden
www.jgg.se
You can see it here:

Vapin' Heathen | youtube.com

Unfortunately it's not a classic ccell head but one of these gurgly cup-style heads. Also it seems you have to use this proprietary drip tip. An absolute no go. Couldn't they just make an ordinary ccell MTL head!!!?


Thanks, I agree with you not really what I wanted
 

Fearlessleader

Senior Member
ECF Veteran
Verified Member
Sep 11, 2014
296
179
63
Portland TN USA
You're killing me here. I already have a lifetime supply of the original :laugh:

Why What version of Ccells did you buy and a lifetime? What u must be like 70 or something LOL Really did you buy the Nickel or the Kanthal. Now if you got the Kanthal I pity you no matter how much you bought but as long as you got the whatever Nickle .20 coils they rock and since I would think that at the worst you would change out a coil a month.


I really don't have any idea why this thread goes on and on the Ccells are good at least the nickel ones the Target key is fine everything works jim dandy it like a 50$ kit it also very good as value how much can be said about this so now don't worry and I really hope u did not really buy like a 1000 Ccells that would such bad but now if you bought say a 100 of the nickel heads your in good shape! Nothing in vaping is expensive Well at least not where you're in a thread chatting about the target. There must be 200 or more kits in the 20 to 200 range. So how tragic can it be!
In about a month maybe 20 they will come out with the perfect Ceramic using tungsten for the heating element there is already some stuff in the works and once they work out the last of few bugs folk will buying RBA'S but for a whole nother reason because you want to not need to.
I really like this mod truthfully but then again I have like 20 PVD's and 35 addy's here easy ever few months I have to order dozen batt's to and 6 to 10 120ml bottles of juice from Metrovapor every Crazy 120 sale.

But ya with all that junk I am buying all the time, I am still using every day my Provari V1 with a Kayfun lite or plus whatever it was at the time I bought my starter kit. I did send it in and the V2 upgrade was done to it.
Vape gear as long as it's made at least halfway decent and like I said, I vape it some every day. The Target Starter kit with the Ccell is the same way, it's fine till the next cool deal comes along. I wish I had a 100 Ccells in my vape Cabinet!!
Vape Gear is not like getting married make you think oh my god what have I done every time you out someplace by yourself and get chatting with some really hot bad think what the hell was I thinking that day someone wake me up *ROTFLMAO*
Realy most that crap that target came out with none of it looks like a game changer but that little coil :)
Just about a week ago The updated Wismec Reuleaux RX200S and I said I never buy one unless I got the DNA version But there was a smoking sale so I got that eVic mini 75watt. oh! and it came with the Tron-s The are almost the same just 3rd in size and wattage 1 battery, not 3. So But the funny part was, the Mini cost like 7 or 8 bucks more Must be like lite beer or near beer would be a better comparison
And a bunch coils, SMOK VCT Ni200 coils, Ccells, Authentic Griffin 25 RTA. I had 2 of the 22mm versions. I really loved that single coil set up on the 25mm deck I blew like 150 bucks so I could get the DHL shipping free but it was worth it as all the stuff had a great price. Wow, that was fast shipping like 3 days later it was at my door.
When I first started vaping it was 180$ for my Provari V1 15 WATTS !!!! Ya smoking baby!!! LOL, charger 2 AW Batt's But I still have it LOL!

See my point Ok I got a run I was only coming here to look up a good wire gauge combo the make 316L Clapton coils.

Have nice day guys SEE YA !!
That was my 1.50$ worth so I hoped someone like it Phuu my fingers are tired



 

salemgold

ECF Guru
Supporting Member
ECF Veteran
Verified Member
Jul 5, 2010
28,155
63,784
South Carolina
Been using the kanthal cCells for many months now and love them. I get 4-6 weeks and more from each coil. You do have to know how to prime and break them in. After that they are amazing. Easy to dry burn to clean and last a very long time.

Maybe I should be the one that has pity for you? These things are absolutely amazing when they are used correctly ;)
 

Junglegeorge

Senior Member
ECF Veteran
Verified Member
Dec 10, 2011
128
184
63
Sweden
www.jgg.se
Been using the kanthal cCells for many months now and love them. I get 4-6 weeks and more from each coil. You do have to know how to prime and break them in. After that they are amazing. Easy to dry burn to clean and last a very long time.

Maybe I should be the one that has pity for you? These things are absolutely amazing when they are used correctly ;)

I agree with with you, tried ni and both ss ccell's still prefer 0.9 kanthal.
Gives me what I like, a rich clean flavour from a ready-made coil. Have no time for twisting coils by myself. Been vaping since 2011 and want it easy. Making my own e-liquid is enough. Keep calm and vape on [emoji100]
 

Ding

Vaping Master
ECF Veteran
Verified Member
Jul 25, 2013
8,717
12,591
Molon Labe
welp,still have my pre-production target kit and it is still firing.I use the target tank everyday.It has a one juice use with my cCells.I got a pack of the cruddy cCells but still a head will last me more than month.love them cCells.Really would like to get the new upgradable Target mod.Wanna try the SS cCells in Target tank.Won't use the Ni coils period.
 
Last edited:

Fearlessleader

Senior Member
ECF Veteran
Verified Member
Sep 11, 2014
296
179
63
Portland TN USA
welp,still have my pre-production target kit and it is still firing.I use the target tank everyday.It has a one juice use with my cCells.I got a pack of the crudy cCells but still a head will last me more than month.love them cCells.Really would like to get the new upgradable Target mod.Wanna try the SS cCells in Target tank.Won't use the Ni coils period.


I don't think we will see much in the ceramic coils till they get ready to have devices. That can run tungsten right now there just dabbling with ceramic coils and there also thinking that they might not want to make them as well . If they come out with the coils I seen with the tungsten cores you won't need to buy more than a coil or 2 a year
the ones I have seen in the write up about the future of the ceramic coil once the get the embedded tungsten ceramic coils it will be, Dry burn and go :) mostly you will buy different coils for if you want mouth hit or lung hit more or less air flow stuff like that. I have seen some place some has already released one built like that with a different core metal alloy and the price was not like the Kanger stuff or Aspire think it was in that $150 to $200 range and they made it sound like they were going to make sure they were not going to have any of that clone jazz with them either. Not sure how they planned that, but I think that was part of why they have not released it yet
 
  • Like
Reactions: cooladdict
Status
Not open for further replies.

Users who are viewing this thread