Alexander Mundy's Magic Twisted Ribbon
- Thread starter Alexander Mundy
- Start date
- th_trl_thread_readers 0
- Status
I don't know about anyone else but an increase in throat hit without an increase in vapor volume doesn't sound like something good is happening. That sounds like you're getting dry coil/burnt juice/acrolein formation.
Which would not be surprising given the "design" of this coil.
Which would not be surprising given the "design" of this coil.
Last edited:
I did a little reading and decided that since acrolein formation is a natural occurrence in french fries... I just HAD to try it in my NEMP rig!
Mr. Mundy, you've done it again! French fries be damned! That is a delicious vape!
Sent from the zoo using Tapatypo 2
Told you dam kids to chill!
I just disassembled my RM2 & drilled out the posts for fun mostly; but also to make some room for Mundy's Magic. 6 wrap, crimped tight; farking delicious. Little slow, tho, at .8Ω. Think I'll pull a wrap. Yeah, and Mundy, now that I've got one scrunched, I'm getting some big poppage. Incredible flavor tho!
I just disassembled my RM2 & drilled out the posts for fun mostly; but also to make some room for Mundy's Magic. 6 wrap, crimped tight; farking delicious. Little slow, tho, at .8Ω. Think I'll pull a wrap. Yeah, and Mundy, now that I've got one scrunched, I'm getting some big poppage. Incredible flavor tho!
Yeah. a drilled RM2 would be necessary for regular use of this stuff. I had to beat the above dualie into submission. The dual 4/5 wrap meters in at about .4-.5ish. Running on a fused mod. Heat-up is on-par with a tight-twisted.7Ω R41 COT coil.
Ok my first attempt with .05 x .1 ribbon wire, wrapped out at 1.1 ohms...
How's this look?
Dan
How's this look?
Dan
Took 21 foot (3 X 7ft) of ribbon to make 43 inches of magic this weekend and that was without any screw ups.
Measured the whole piece and it was 20.3 ohms for 5.665 ohms/ft or .472 ohms/inch.
The ribbon is 10.8 ohms/ft so almost a 2X reduction in resistance but with 3 pieces together.
So I got 60% more surface area per ohm than if not twisted and interlocked.
Should be at least 3 maybe 4 more joining us for fun within a week.
If the supplier of .6X.07 ribbon ever gets back from vacation I hope more.
Soon we will take over the world......Mah...Ha..Ha..Ha.
Sorry, momentary lapse of sanity.
Back to reality now.
Measured the whole piece and it was 20.3 ohms for 5.665 ohms/ft or .472 ohms/inch.
The ribbon is 10.8 ohms/ft so almost a 2X reduction in resistance but with 3 pieces together.
So I got 60% more surface area per ohm than if not twisted and interlocked.
Should be at least 3 maybe 4 more joining us for fun within a week.
If the supplier of .6X.07 ribbon ever gets back from vacation I hope more.
Soon we will take over the world......Mah...Ha..Ha..Ha.
Sorry, momentary lapse of sanity.
Back to reality now.
I'd be lying if I said I have made my own at this point, but from what I can see it looks pretty durn good there! I need to get some ribbon ordered and make myself a pile of this stuff.
To answer a previously asked question: I have re-wicked and dry-burn cleaned the single coil I built about a week ago 2x now and it cleans up beautifully.
To answer a previously asked question: I have re-wicked and dry-burn cleaned the single coil I built about a week ago 2x now and it cleans up beautifully.
Ok my first attempt with .05 x .1 ribbon wire, wrapped out at 1.1 ohms...
How's this look?
Dan
Hey, nice to see you here Dan!
That looks pretty dang good!
I assume you meant .5 X .1 ?
I didn't get as good a results with .5 X .1 as I did with .6 X .07 but it was better than round or flat ribbon.
I tried .05 X .1 and didn't get anything that looks anywhere near as good as that!
If that is .05 X .1 I tip my hat to you and bow down.
Can you scan a small piece of it with a scanner at 1200 DPI?
I can tell you more with that kind of resolution.
Please let me know the results either way.
PS, mail goes out tomorrow. wink wink
Last edited:
I dry burn mine once or twice a day when I change wick(s) to change flavor.
(I like to do that a lot in case you didn't get it)
Hey, nice to see you here Dan!
That looks pretty dang good!
I assume you meant .5 X .1 ?
I didn't get as good a results with .5 X .1 as I did with .6 X .07 but it was better than round or flat ribbon.
I tried .05 X .1 and didn't get anything that looks anywhere near as good as that!
If that is .05 X .1 I tip my hat to you and bow down.
Can you scan a small piece of it with a scanner at 1200 DPI?
I can tell you more with that kind of resolution.
Please let me know the results either way.
PS, mail goes out tomorrow. wink wink
I have a magnifier adapter for the iphone will hook it up and take a pic, yes sir you are correct .5 x .1 the .05 was a typo.
Thanks wink wink
Dan
Added:
Any Better?
Dan
Last edited:
Just tried it, Holy Crap I have never gotten that kind of performance from a single wrap standard kanthal wire
Yoza!
Dan
Yoza!
Dan
Mr. Dano. Next you should dive into cotton wick. But be prepared to have your mind BLOWN!
wink wink!
well, my 6 wrap quickly became a 3/4 @ .5Ω and I'm a happy camper!
But, the reason I write to you, gentlemen, is one of confusion. What's up with the resistance on this stuff? Am I just being stupid? ( . . .. don't)
If I do a 3/4 wrap and get .5Ω (or .4Ω on my other 3/4 wrap), then how come Xoxo gets to do a dual 4/5 and net the same? What kind of res. have you been getting, Mundy? (I recall that the initial #s you sent me with the sample pieces was also substantially higher than what I'm finding.)
well, my 6 wrap quickly became a 3/4 @ .5Ω and I'm a happy camper!
But, the reason I write to you, gentlemen, is one of confusion. What's up with the resistance on this stuff? Am I just being stupid? ( . . .. don't)
If I do a 3/4 wrap and get .5Ω (or .4Ω on my other 3/4 wrap), then how come Xoxo gets to do a dual 4/5 and net the same? What kind of res. have you been getting, Mundy? (I recall that the initial #s you sent me with the sample pieces was also substantially higher than what I'm finding.)
Well enhanced as best I can with what I have and still can't tell for sure, but I believe you have the technique down.
More importantly than what I think, hows it vape?
More importantly than what I think, hows it vape?
- Status
Similar threads
