Are YOU a Tootle Puffer??

[AXIOM_1]

How clever is that I posted a nothing hehe

lol --- makes more sense than what I usually post

 

[DPLongo22]

sun + dry = sundry

Tomato.

 

[Robert Cromwell]

No it is Tomato.

 

[AXIOM_1]

Tomato.

 

[anjelvape77]

Exactly that. I struggle with it already (though the new scrip for Advair 500/50 seems to be helping a lot more than the 250/50 did), tootle puffing my Achilles at 8.5w, 1.7Ω coil, 86% PG. Any more vapor than that just about puts me on the floor.

Andria

I'm glad to hear the new script is working better for you

 

[DPLongo22]

No it is Tomato.

TOMATO!!!

 

[Katdarling]

Jiffy.

 

[Krisma]

Jiffy.

JAFFA

 

[The Ocelot]

Jiffy.

You're so choosy.

 

[DPLongo22]

You're so choosy.

"...mother."???

 

[AXIOM_1]

You're so choosy.

lol

 

[gt_1955]

Sunday morning, felt like a play so ...

EVOD: modified to the max

Chimney drilled to 3ø ID
Atty holder wick channels drilled to 2ø
Positive pin drilled to 2ø ID
Positive pin "big end" turned down by 1mm OD
Base air holes (all 3) drilled to 1.4ø
6/7 wrap tensioned contact coil 1.1Ω around a 2ø mandrel
Hollow coffee filter wick
Rayon flavour wick

11.5W, plenty of vapour and throat hit

 

[Krisma]

Sunday morning, felt like a play so ...

EVOD: modified to the max

Chimney drilled to 3ø ID
Atty holder wick channels drilled to 2ø
Positive pin drilled to 2ø ID
Positive pin "big end" turned down by 1mm OD
Base air holes (all 3) drilled to 1.4ø
6/7 wrap tensioned contact coil 1.1Ω around a 2ø mandrel
Hollow coffee filter wick
Rayon flavour wick

11.5W, plenty of vapour and throat hit

So you don't have a hangover then

Was it a good party.

 

[Robert Cromwell]

Sunday morning, felt like a play so ...

EVOD: modified to the max

Chimney drilled to 3ø ID
Atty holder wick channels drilled to 2ø
Positive pin drilled to 2ø ID
Positive pin "big end" turned down by 1mm OD
Base air holes (all 3) drilled to 1.4ø
6/7 wrap tensioned contact coil 1.1Ω around a 2ø mandrel
Hollow coffee filter wick
Rayon flavour wick

11.5W, plenty of vapour and throat hit

Similar to what I did. You use 30ga wire?
Only drilled the pos pin to 1.6 though. Will try 2.0. they vape well don't they?
The T3 with the same coil seems to vape a bit better than the Evod though, and I only use a cotton wick with no flavor wick and no leaks or gurgles in the T3 or the Evod.

 

[gt_1955]

I used 28AWG NiChrome60 (I prefer NiCr over Kanthal). There's too much air for good flavour, but was a fun thing to do

 

[Robert Cromwell]

I just ordered 5 more T3S's for under $14. They are getting a bit more difficult to find and most places want around $5 each for them.
With the bored out 1.4 ohm coils the juice does not last long in the Evods.

 

[gt_1955]

So you don't have a hangover then

Was it a good party.

Too old for hangovers It was a very pleasant evening though, had a lot of fun and I reckon the youngsters *might* have gone out later.

 

[Robert Cromwell]

I used 28AWG NiChrome60 (I prefer NiCr over Kanthal). There's too much air for good flavour, but was a fun thing to do

Maybe I will not drill out the bottom pin then, my flavor got a bit better after drilling and going from a 1.6 mm coil to a 2.0 mm coil.
Mine are 1.6 mm pos pin hole with a 2 mm stem hole and wick slots enlarged to 2 mm.
I use Kanthal.

 

[Krisma]

I finally worked out how to properly kick my crisscross max this morning so the new one will be VV

 

[gt_1955]

I just ordered 5 more T3S's for under $14. They are getting a bit more difficult to find and most places want around $5 each for them.
With the bored out 1.4 ohm coils the juice does not last long in the Evods.

Doesn't last long at 1.1Ω either