Ask IMAGINE & S_Steve - Thread :)

Status
Not open for further replies.

cindycated

ECF Guru
ECF Veteran
Verified Member
Jul 19, 2011
10,304
30,936
San Francisco, CA
Whew, I saw it on another post and couldn't believe my eyes! :shock: Imagine, what's the "official" cut-off time? I'm thinking of switching to Spinners exclusively, and this is something I should know first...hoping for a nice and long 10 seconds, like on the manual X2s (but would probably be OK with 7+).
 
Last edited:

The Soot King

Full Member
Verified Member
Jun 11, 2012
56
26
High among the chimney tops
Can I use any mini-USB cable to charge my Volt X2 or is there something particular I need to look for? The reason I ask is because the cable that came with my X2 frayed very badly at the joint so I do not feel comfortable using it (and it doesn't charge anything particularly well) and I don't see replacement cables listed on the SI website.
 

cindycated

ECF Guru
ECF Veteran
Verified Member
Jul 19, 2011
10,304
30,936
San Francisco, CA
Can I use any mini-USB cable to charge my Volt X2 or is there something particular I need to look for? The reason I ask is because the cable that came with my X2 frayed very badly at the joint so I do not feel comfortable using it (and it doesn't charge anything particularly well) and I don't see replacement cables listed on the SI website.
I think replacement cables are free - you just have to ask them for one. You can use any mini (I went out and bought a better quality one), but if you use non-SI ones, you'd void your warranty.
 

Imagine

Unregistered Supplier
ECF Veteran
Mar 16, 2011
7,040
13,915
OHIO USA
www.SmokelessImage.com
CS can send you out a new cord if you like :)
Can I use any mini-USB cable to charge my Volt X2 or is there something particular I need to look for? The reason I ask is because the cable that came with my X2 frayed very badly at the joint so I do not feel comfortable using it (and it doesn't charge anything particularly well) and I don't see replacement cables listed on the SI website.
 

Imagine

Unregistered Supplier
ECF Veteran
Mar 16, 2011
7,040
13,915
OHIO USA
www.SmokelessImage.com
it should be 10 sec on the spinner.
Whew, I saw it on another post and couldn't believe my eyes! :shock: Imagine, what's the "official" cut-off time? I'm thinking of switching to Spinners exclusively, and this is something I should know first...hoping for a nice and long 10 seconds, like on the manual X2s (but would probably be OK with 7+).
 

Grimwald

Vaping Master
ECF Veteran
Aug 12, 2012
3,666
5,439
Lawrence KS
Quick question. If an X2 battery is shot...no longer holds a charge...it will not work in passthru mode...right? I don't have any yet, but I do have one getting a little weak, and I'm trying to decide if I should pick up a couple of regular straight passthrus. Also, the regular passthrus only work on a 1.5 plug...is that also correct? Can I use the regular passthrus on something higher...like a 2 amp plug?
 

Imagine

Unregistered Supplier
ECF Veteran
Mar 16, 2011
7,040
13,915
OHIO USA
www.SmokelessImage.com
Once a x2 is dead it will not function in passthrough mode. The regular passthrough needs a min 1.5a to fire anything higher is fine.
Quick question. If an X2 battery is shot...no longer holds a charge...it will not work in passthru mode...right? I don't have any yet, but I do have one getting a little weak, and I'm trying to decide if I should pick up a couple of regular straight passthrus. Also, the regular passthrus only work on a 1.5 plug...is that also correct? Can I use the regular passthrus on something higher...like a 2 amp plug?
 
Status
Not open for further replies.

Users who are viewing this thread