Awesome, thanks for that info. Tomorrow I'm going to introduce a friend to vaping, and try to get her to get one of those if she wants a setup of her own.
Attack of the (Kayfun v4) Clones!
- Thread starter KTMRider
- Start date
- th_trl_thread_readers 0
- Status
Awesome, thanks for that info. Tomorrow I'm going to introduce a friend to vaping, and try to get her to get one of those if she wants a setup of her own.
Yep they are not supposed to be released till the 19th. I am thinking real seriously about ordering an hcigar and paying the extra 10 bucks.
I see everyone has the Sub tank on sale. Must be because the new sizes are coming out and they will be a lot more popular.
Darn, at work last night I saw that someone had put 3 of those aluminum disposable roasting/baking pans next to the recycle bins, they were unused. At the time I didn't think about it but a little piece of one of those would be about the right thickness.
That's a good idea. I'll have to scrounge around since I don't have any money until friday xD
What's the best build to put in one of these for a mechanical mod? I've got a 1.6 ohm build in mine and it's doing OK in the mech. I was thinking of removing a coil and maybe dropping down to 1.2 ohms. Would sub ohm in this tank be a bad idea? Would the wick be able to keep up?
Got my eBay Tobeco about 20 mins ago, got it soaking in some dish soap.. So to fill it, I just dump juice through that top piece with all the air holes or what?? Wish they threw in the parts diagram, but that's what the internet is for!
Mine came with an extra spring inside the clear tank, no other spares though.
Mine came with an extra spring inside the clear tank, no other spares though.
make sure to shut off the juice control so you don't flood the tank
then fill, then top cap, then open the juice control
then fill, then top cap, then open the juice control
Paying more doesn't necessarily get you a better clone. Look at the Robbottech version. Not very good at almost twice the cost of a Tobeco or FT clone.
I can almost guarantee that one of the ones at FT and the Hcigar one are produced in the same factory just put in a different box
Hcigar is like Sear and Roebucks, they make nothing , only market it.
almost = no guarantee
Last edited:
Yeah the juice control threw me off when I was taking it apart haha. Couldn't figure out why I couldn't get the base off! Had to use vice grips on the air ring to get the chimney off.
Guess I gotta watch Phil's video, this definitely ain't as simple as the KFL!!
Guess I gotta watch Phil's video, this definitely ain't as simple as the KFL!!
Got the EHPRo version in. It's taking a Dawn bath at the moment. Threading is great. Glass section has a minor flaw. Just a small hint of machine oil. The juice control does work as supposed too. On both Tobecos I received, you have to loosen the 510 pin to get it to work. One Tobeco stopped moving all together and the deck has seized. Right now, unless i have time to really fiddle with it, it is spare parts. The drip section on the EHP is round...but the Tobeco flat does fit.
The EHP version did come with spare o-rings and such.
The EHP version did come with spare o-rings and such.
next time, make sure your deck/juice control area is seated properly before trying to remove that. I find having it in the correct position absolutely crucial with this device and trying to take it apart.
anyone have a suggestion to stop the leaking @ #16 oring? I wrapped dental floss around it, one wrap. any more and it wouldn't fit. but after a few hours my 510 is full of juice still 
kinda bummed, it worked so good for the first couple days and then started leaking...
kinda bummed, it worked so good for the first couple days and then started leaking...
I found for mine the juice control has to be fully opened, or fully closed
might need to get a fatter o-ring
when using floss like that, as it gets wetter, it won't be as thick as when you initially applied some. might need a bit more
might need to get a fatter o-ring
when using floss like that, as it gets wetter, it won't be as thick as when you initially applied some. might need a bit more
First tank with the Tobeco going down! No leaks, glass tanks nice and snug.. Honestly its not much different from my EHPro KFL.. Actually I'm getting less flavor outta the same juice that's in the KFL but its still a "new" wick so.. Gotta pull the 510 out and tighten the airflow still too but aside from that, spot on Tobeco!!! The one from Artemus should be here tomorrow too hehe..
anyone have a suggestion to stop the leaking @ #16 oring? I wrapped dental floss around it, one wrap. any more and it wouldn't fit. but after a few hours my 510 is full of juice still
I used cotton thread. About 10". I just got my o-ring order so I'll try that soon but no leaks so far.
My tracking # still shows "pre-shipment"
- Status
