Ive charged it a few times with the USB. But its usually on my desk when im doing it so i can keep an eye on it. Since im not sub ohming i dont have a whole lot of concern for the battery. Well, withing reason.
- Status
same here. I charge via USB. In the dark I can see the red glow through the side of the screen. When it stops glowing, I know it's ready
Last edited:
Well I bought one! Love it!! It's nice to have a device that I can put anything on and not worry. Now I just have to find a wrap... Not liking the textured finish.
Sent from my iThingy using Tapatalk
Sent from my iThingy using Tapatalk
Well I bought one! Love it!! It's nice to have a device that I can put anything on and not worry. Now I just have to find a wrap... Not liking the textured finish.
Sent from my iThingy using Tapatalk
Magma and Cloupor is a mighty mighty combo. That has been my daily rig for a few weeks now and I dont see that changing anytime soon.
Good to hear everyones onboard charging seems to be working. You guys have put me at ease. Thanks!
I was very skeptical as well, but so far, it's seemed pretty solid.
has anyone found wraps for these that they know will fit? Ive heard the ones for the original hana wont fit and i dont want to spend $18 + shipping to find that it is off by a few mm.
Great thread btw
Great thread btw
Just got mine today, so far its great. Did a .7ohm build in my atomic clone and at 14.5w the flavor is great. Only thing is the battery seemed to go pretty quick.
Whats been everybodys preferred build and wattage to optimize battery life.
Whats been everybodys preferred build and wattage to optimize battery life.
If you sub ohm the battery will go pretty quick. If I use 1.4, 1.5 ohms in a Kayfun it will last almost 3 tankfuls.
Did you dig out all the old glue and resin? Did you use existing buttons and charge port? How about some pics.
I only dug out enough glue to get the chip out, I used existing wires, buttons, and charge port. I'd upload some pics but I put the red cover back over the wiring so you wouldn't be able to see anything.
Another thing is, I own like the first version with logo, and the whole coming out of sleep mode drove me crazy.
Sent from my iPhone using Tapatalk
Another thing is, I own like the first version with logo, and the whole coming out of sleep mode drove me crazy.
Sent from my iPhone using Tapatalk
It doesn't look as clean as it did before though...
Sent from my iPhone using Tapatalk
Not bad. I've got one that crapped out completely. I gutted it. I'm not sure what I'm going to do with it. I'd like to figure out if I could get an SX350 chip in it.
I have made a couple sx350 boxes, the chip will fit, but the screen cutout might look a little ridiculous because it would be too big if you cut the square to the length of the hole that's already there. I just used a Hammond 1590g for mine
Sent from my iPhone using Tapatalk
I've read that it won't fit. At any rate here is a link to a pdf.... you can download it and then zoom it to see the measurements...or zoom it in the link....
https://docs.google.com/file/d/0B61oDGxskBGhRkJIa05jbXlDdVE/edit?pli=1
I have made a couple sx350 boxes, the chip will fit, but the screen cutout might look a little ridiculous because it would be too big if you cut the square to the length of the hole that's already there. I just used a Hammond 1590g for mine
Sent from my iPhone using Tapatalk
What kind of battery setup did you use for that?
I have an 18650 directly soldered in there, it's pretty messy but it gets the job done! I have another one in a 1590a box with two 1200mah lipos. I'd show you a pic but its not with me
Sent from my iPhone using Tapatalk
I took the vtc5 out and replaced it with the efest 3100mah batts and my battery life is awesome. With my vape habit and a setup of 2.5Ω single coil in my trident v2 I can go a day and a half before charging. I had a sub ohm build before, battery life is definitely not there but now my builds hover around 2-2.5Ω A lot of room for me to either have a cool or warm vape.
- Status
Similar threads
