Debuting - The GotVapes SMOK TiTaN - 5-6ml Polypropolene Modular Tank - Replaceable Stem Coils, All Colors, DUAL COIL HEADS! - AVAILABLE NOW!
- Thread starter dannoman
- Start date
- th_trl_thread_readers 0
- Status
I just got my pretty pink Titan and it's leaking from the bottom of the tube. Any suggestions? I've got everything screwed on tight, but have a constant seeping from the bottom edge of the tube. Should I try getting another tube for it?
oh noooo ! 
Make sure the head is screwed on tight. Also could be the o-ring is missing on the head section.
Or did you mean the tank itself and not the center post?
I'll check for that o-ring when I get it apart. I made sure the head was screwed in tight before I filled it. It's not leaking from the bottom of the post, seems to be seeping from bottom edge of the tube 
ya mean on the outside tank sleeve right ?I'll check for that o-ring when I get it apart. I made sure the head was screwed in tight before I filled it. It's not leaking from the bottom of the post, seems to be seeping from bottom edge of the tube
I'm wondering if where the threads are glued or whatever inside the plastic might have a leak there maybe ?
I would try and gets another sleeve prollys, but I no experts on it. What's ya think Wally ?
Here are a few ideas to look for ( actually feel for )...
Remove the o-ring from the bottom cap and run it between your fingers to see if you can feel any nicks or other deformities.
On the bottom cap, if you can get your finger to feel in the area the o-ring sits in that bottom corner... again run your finger around to feel for nicks etc. Repeat the same for the tube where the o-ring seals up to it.
It appears that the tube can be put on in either direction ( top and bottom appear the same in the pics )... If you don't find anything I suggested above... try putting what had been the top of the tube onto the bottom cap... in otherwords, just turn it over.
Thanks Rdsok, gotta get the juice out and clean it so I can do that
Edit:can't just turn it over, the fittings are a different size between top and bottom, can't reverse. got it apart to clean, so will check the o-rings
Edit:can't just turn it over, the fittings are a different size between top and bottom, can't reverse. got it apart to clean, so will check the o-rings
Last edited:
I'll check for that o-ring when I get it apart. I made sure the head was screwed in tight before I filled it. It's not leaking from the bottom of the post, seems to be seeping from bottom edge of the tube
Could be that ring pressed in the tube is seeping. Maybe it's just the one end. Try flipping it. Should slow the seepage being on top.
Yiddle, my blue one does that as well. Has since I got it. I ordered a pink one but have not tried it yet. I am hoping it does not seep. Let me know if you try another tube and it works.
Take a good look at the orings on the caps also and make sure they are screwed down tight. Try swapping your upper and lower oring seals. I'm just guessing because I'm not 100% sure where you are getting leakage. Did you try flipping the tube end for end and reassembling?
I know I'm wearing this out but I had a stem that even after adjusting the ceramic cup was still vaping hot. I trimmed just the tiniest bit off the bottom edge of the silicone cap and untwisted the wicks using a dental pick. Huge improvement though the trade off is having to tip the tank down more often.
The plastic tube extends just a hair beyond the metal on mine and checking it out, it was a bit ragged feeling. I'm thinking that may have affected how it sealed when screwed together. I've tried to smooth it out and am going to see if that elimnates the problem. If it's only IT and me, that's not too bad, out of how many?
Yea....not too bad...mine is leaking from the same spot as yours. It leaked when I got it, although not too bad and I just wiped it dry every vape or so...then I dropped it and it got a little worse. The thing is, I cannot find any damage or reason for the seeping. The only place it could be coming from is between the metal ring where it is attached to the tube.
Did you and yiddle try flip flopping your tubes end for end? The odds on both ends leaking are pretty slim unless you are missing o-rings. Or the bottom cap itself is damaged with a nick or something.
- Status
Similar threads
- Locked
- Locked
- Locked
- Locked