Eleaf Lemo II
- Thread starter Vapenstein
- Start date
- th_trl_thread_readers 0
- Status
Just when I thought I wasn't going to buy anything else. I don't care about the airflow as much as the side fill. Filling the Lemo just kinda sucks. Hope they cure the minor leaking into the base issue as well.
Are those the only changes? The filling and airflow? If so, I'm not feeling any great need to get one. Neither bothers me much from the first version.
it also looks like the overall airflow has been increased by the looks of the new drip tip
I agree. The only thing I need in V2 is access to the build deck while full....and a couple of tabs next to the post screws wouldn't hurt!
Don't want it. All of these features are going to make it taller by the looks of it. That and the fill design looks like a leak waiting to happen.
i don't like these changes either. i just picked up a lemo drop from a b&m. i like the fill hole on the bottom because some leaking is to be expected and at least the bottom cap acts as a reservoir.
i can expect the side fill hole to leak as well. there were some awful ce3's back in the day that required a weirdo and very lose-able silicone plug. i am not stoked to see its return. guess i will have to pick up two lemo's to complete my setup sooner than expected.
i can expect the side fill hole to leak as well. there were some awful ce3's back in the day that required a weirdo and very lose-able silicone plug. i am not stoked to see its return. guess i will have to pick up two lemo's to complete my setup sooner than expected.
Oh, yeah, that enormous drip tip would have to go. I'm not much of a lung inhaler, and its possible to make a wide bore tip without it being the size of a donut.
How can you do a mouth to lung hit on this airflow? I used to only do mouth to lung, but then I got a kayfun, and most recently I have been replacing the Kayfun with Lemos, and really decking them out - looks sick.
What the flip google? Where are the pics of the Lemo II's innards? Inquiring minds want to know!
I've been waiting for version 2 since August... I was hoping that they would just make a 22mm version with improved airflow control, but it looks like they turned it into another subtank with huge airflow.
That drip tip looks like a stove pipe. If the hole in the deck is the same size, it's not for me either. I'm a lung-to-mouth person who just happens to like nice open airflow.I want to see the deck...
Last edited:
Not jazzed about the drip tip. With that capacity it doesn't seem to me like it would be as tall as the original Lemo, and a drop version of this wouldn't hold much. We need reviews. Or previews. Whatever.
I'm gonna reserve judgment until I see previews or reviews and get more information on the tank. I like the fact that it isn't bottom fill anymore if nothing else.
Pulled from Heavengifts.com:
How to DIY
Pls wrap the heating coil around the absorbent cotton according to your demand and then fit it on the atomizer base.
Note: Please do not dry burn the cotton directly, otherwise it might get on fire. Drip little e-juice in the absorbent cotton to make that moist before filling in the e-juice.
Really curious to see the build deck and how it wicks if they want the coil wrapped around the cotton, not the cotton threaded through the coil once its mounted.
How to DIY
Pls wrap the heating coil around the absorbent cotton according to your demand and then fit it on the atomizer base.
Note: Please do not dry burn the cotton directly, otherwise it might get on fire. Drip little e-juice in the absorbent cotton to make that moist before filling in the e-juice.
Really curious to see the build deck and how it wicks if they want the coil wrapped around the cotton, not the cotton threaded through the coil once its mounted.
Honestly, unless you're using silica or mesh, I would just build it the usual way
My Lemo has never leaked with the bottom fill screw. I do get a little condensation in the well sometimes.
Seems like it would be easy to open the fill hole and dump the tank for servicing the deck. Better than spilling the juice everywhere with current design I guess.
The top fill concerns me though. It's much easier for air to leak past a seal than for liquid to. If air leaks in that fill hole vacuum will be lost and the tank will drain out to near empty.
Reduced juice capacity is not encouraging. 3.8mils? I vape that much over morning coffee.....almost.
New AFC is easier, looking at the pics. Hope it has heavy friction. Airflow is critical to me and I can't stand for adjusters to move with normal use. In and out of pockets...etc. Also wondering if there is an airflow slot on the other side of the base as well.
There appears to be a gap between the upper and lower chimney sections. Hoping it's just not tightened all the way.
Wonder what else they changed.
The top fill concerns me though. It's much easier for air to leak past a seal than for liquid to. If air leaks in that fill hole vacuum will be lost and the tank will drain out to near empty.
Reduced juice capacity is not encouraging. 3.8mils? I vape that much over morning coffee.....almost.
New AFC is easier, looking at the pics. Hope it has heavy friction. Airflow is critical to me and I can't stand for adjusters to move with normal use. In and out of pockets...etc. Also wondering if there is an airflow slot on the other side of the base as well.
There appears to be a gap between the upper and lower chimney sections. Hoping it's just not tightened all the way.
Wonder what else they changed.
I got a feeling that's just Engrish and you still build it the traditional way.
- Status
