Yeah, I just didn't think the airflow was very good, not as good as it should be for how they market it (and half the design). Should be at least as airy/open as most of the sub ohm clearos, and its not.
Eleaf Lemo II
- Thread starter Vapenstein
- Start date
- th_trl_thread_readers 0
- Status
Would you mind laying out the Details on your Ti Builds? Help me get a starting point on what is working well with Ti on the Lemo 2 prior to.
Lemo 2 arrived yesterday and just waiting on the 26 ga Ti wire form Unkammen to arrive Friday to build. Have some 28 ga and it's great for a Dual Coil Build in the El Cabron rda for TC on my SX Mini M but pretty sure on the single Coil Lemo 2 that 26 will be best.
I've had the Lemo 2 for about a month and it is definitely my favourite... until this morning when i received my Goblin. I think this is going to be a close competitor. 
But I still love the Lemo 2 - so well made and such good flavour.
But I still love the Lemo 2 - so well made and such good flavour.
Wait until you refilled the Goblin a few times. My v2 drove me mad and is retired now.I've had the Lemo 2 for about a month and it is definitely my favourite... until this morning when i received my Goblin. I think this is going to be a close competitor.
Got my Lemo yesterday. Was excited, but then I took it apart to do my first build and this is what I found:
Imgur
What on earth is that gunk? Its waxy. Not machine oil.
Imgur
What on earth is that gunk? Its waxy. Not machine oil.
Last edited:
You got a picture of that? Never seen one. I've just heard of build decks.
Thanks but it's fairly easy to build with a little practice. It's a dual twisted 28g kanthal, 6 wraps on 2.5mm. comes out to .45 ohms and is perfect in the ST at 22w. I'm vapin Wakonda in it now on a resurrected iStick 30w I've been workin on.
Ugly, you'd better wash it about 5 times and boil it for 30 minutes...
ETA: @Azarius. This looks the same as the build deck in my Lemo. Yours too
Last edited:
Yes it is. I#ve never seen something alike either. I'd boil the whole atty for a while and clean it with soap and a toothbrush. Your picture doesn't have the best quality but from what I can see it looks nasty.
My Lemo 2 was completely clean.
Better pictures here:
Maybe FT or eLeaf will get back to me and replace it. I contacted them when I saw it. It's not oil, that I know. Its waxy, like melted plastic or something. Not comfortable smoking on it even after a boil. Plus I am sure if I do something like that they'll say that's the cause.
Maybe FT or eLeaf will get back to me and replace it. I contacted them when I saw it. It's not oil, that I know. Its waxy, like melted plastic or something. Not comfortable smoking on it even after a boil. Plus I am sure if I do something like that they'll say that's the cause.
Fasttech usually has a great customer service. I never had any problems with them.
Are you sure that stuff on your Lemo isn't alive? Looks like it would eat a cat in seconds.
I used 26g Ti in the Lemo 2.
9 wraps on a 2.5mm rod, I put the legs under the screw heads, it came out at .41Ω on the evic VT, the mod recognised the Ti and set the temperature at 470°F and 32watts. I used a rayon wick.
It doesn't blow competition clouds but they produce a good amount of vapor.
On the VF DNA40 set the temp at about 370°F and 30watts.
I have refilled it from the top - screw off the top while holding the bottom of the glass tank firmly down (much like we do with KF Lite) . You can't fill it all that way because the chimney is short but it can be done.
As promised, I made the top fill hole the way it should have been from day 1. A diamond burr and some water made short work of it. I also discovered the top cap is chrome plated brass.
- Status
