36 pulled right out but I've got some 33 and 32 I'll try. I appreciate you putting them in there.
Jack
Jack
- Status
SammyT you sent me for a whirl! I read that while at work and my head started spinning...I seriously felt incredibly dumbz for a few minutes trying to figure out why my brain was running backwards hahaha
I got reckless and courageous, took the dremel and bored it out with a 3/64 bit, 1/16 looked scary big
The ERA at the bit alive, couldn't even get through all the way so its a hair less than 3/64, but got through enough, draw is perfect now!
What a lucky horse
glad it worked out for ya . I used a drill at a slow speed and took my time chewing through the metal and it didnt eat the bit up at all... maybe that is the best way to do it for those attempting this.It's tough to drill through SS with a flimsy soft bit, just take your time. I used a little juice as lubricant
I drilled mine out at 1/16 today...was going to use 3/32 but thought I would do the smaller hole first and see how it goes. I'm glad I did this- 1/16 is perfect for me!!
Ok, dumb question....what type of wick and wire come with the ERA?
Sent from my DROID RAZR using Tapatalk 2
Sent from my DROID RAZR using Tapatalk 2
i really can't remember as it came unspecified. but the silica was thin, 1 or 1.5 mm, the wire also was thin, a bit less then 0.2 mm (0.32 awg). i prefer 1.5 - 2 mm silica. i guess you can run any thickness of wire on the ERA, depending on what voltage you want to use. haven't tried 0.28 awg kanthal yet, i think this is reserved for mesh rebuildables (what is possible with the ERA too, has been showed in this thread).
here you go I've been using it all weekend as you can see it got a lot of build up on it time for a cleaningAre there any Picts of a SS wick set up
..........
here you go I've been using it all weekend as you can see it got a lot of build up on it time for a cleaning
So you just put the build right on top of the feed hole?
..........
..........
I used the drill bit method once the coil was installed I threaded the SS through its sitting right in front of the feed hole, the only down fall is dry hits with ss are killer so I got to remember to squonk more often
Last edited:
I´m having a little trouble finding wich type of coil to make with the ERA, I made a few by measuring the lenght of wire, using a screw and sometimes using more wick, sometimes less... I´m still looking for a good setup.
I was thinking of opening up a thread for sharing wick & coil setups that work for the Reo´s, what do you think?
I was thinking of opening up a thread for sharing wick & coil setups that work for the Reo´s, what do you think?
Sounds ok to me. I've done several different ohm setups with 32 & 34 Kanthal with 5/6 wraps 2-3" of 3mm silica looped once and always seem to get a good vape. Rarely do I check the ohms and only using them on my VV Reos so I just turn it up as hot as I can without burning my juice
Sent while Hyper Vapin a Trippy Tipped Reo
Sent while Hyper Vapin a Trippy Tipped Reo
Last edited by a moderator:
Suppose to say a good vape but tapatalk won't let me edit my posts anymore
Sent while Hyper Vapin a Trippy Tipped Reo
Sent while Hyper Vapin a Trippy Tipped Reo
for some reason I must know ohms and voltage it drives me bonkers if I don't look
Used to be that way also then I got lazy and figure if I like it what does it matter
Sent while Hyper Vapin a Trippy Tipped Reo
I know most of you guys are anti tube in here but there is enough room heart for some provari w/DID love 
- Status
