I really like my Term-C's with the Oddy to kayfun conversion kits, I have two and these are my favorites.
- Status
I could see you being all over the Aqua ... almost seems like a cross between the two. I have one on pre-order.
Actually I have to refrain from using my Aqua and Origin, it works so well that using them makes me unsatisfied with all my other devices.I could see you being all over the Aqua ... almost seems like a cross between the two. I have one on pre-order.
There would be no going back.
The Aqua clones will be appearing around any day now in the $30 - 35 area
Last edited:
Ha! I knew it! Yep, Origin and Aqua clones both ordered. I immediately thought of Ithaka when I saw the juice control of the Aqua.
I have one brass and one ss Origin clone and an Aqua clone ordered.
I need to clone myself if I'm going to make use of all this gear.
Hmmm I have a plexi carto tank that is almost the perfect inside diameter to be used on the fogger...
Now to figure out how to jimmy rig it in there...
Now to figure out how to jimmy rig it in there...
It was a little to long so I hack sawed a couple cm off it.
Also I had to use slightly different o rings to get a good seal.
My fogger is back alive yay!
Sent from my SCH-I605 using Tapatalk
Also I had to use slightly different o rings to get a good seal.
My fogger is back alive yay!
Sent from my SCH-I605 using Tapatalk
A little tip for those who disassemble their Fogger:
If you look at where the air tube is in the center of the base between the posts where the coil is mounted you can see a silicone insulator with it.
This insulator must not be down in the hole very far on that tube or it will cover two of the four holes where the air enters the tube.
I didn't see this mentioned before but I may have missed it.
I have sent my Fogger to another ECF member for "beta testing", awaiting results, should be hearing something soon.
My real Taifun is doing well and my FT Taifun clone has just passed through Singapore Post, finally.
If you look at where the air tube is in the center of the base between the posts where the coil is mounted you can see a silicone insulator with it.
This insulator must not be down in the hole very far on that tube or it will cover two of the four holes where the air enters the tube.
I didn't see this mentioned before but I may have missed it.
I have sent my Fogger to another ECF member for "beta testing", awaiting results, should be hearing something soon.
My real Taifun is doing well and my FT Taifun clone has just passed through Singapore Post, finally.
Last edited:
So has anyone actually got the fogger working on a consistent basis and been able to replicate their success many times over? I really like the design and look of these and the V2 seems to have addressed many problems of the original like that crap isolator that used to stick up under your coil.
Im particularly interested in cotton builds. I like the taste I get from cotton. Probably wont ever use silica again EVER after using cotton. Id even venture into using ss mesh but again has anyone got this thing running good on a consistent basis? I really wanted to get one of these and I dont mind some minor "tinkering" but I hate stuff that just has to be perfect to work too...
Thanks for your time. This community is great, im 4 1/2 months into my vaping hobby and I love it. I could always use a few more toys in the jouney of finding the ultimate vape!
Im particularly interested in cotton builds. I like the taste I get from cotton. Probably wont ever use silica again EVER after using cotton. Id even venture into using ss mesh but again has anyone got this thing running good on a consistent basis? I really wanted to get one of these and I dont mind some minor "tinkering" but I hate stuff that just has to be perfect to work too...
Thanks for your time. This community is great, im 4 1/2 months into my vaping hobby and I love it. I could always use a few more toys in the jouney of finding the ultimate vape!
I think there are many that have them working well, it's just the ones that don't that we hear a lot about.
I've had four so far, the first being a v1 (favorite) but I modded each one a little before using them. Never had any real problems other than slight flooding when filling but that was expected because of design, I've seen a lot worse with that problem.
Oh, the reason I liked the v1 better is because of the way it's filled. it definitely had more things that needed addressed like air flow and such.
I've had four so far, the first being a v1 (favorite) but I modded each one a little before using them. Never had any real problems other than slight flooding when filling but that was expected because of design, I've seen a lot worse with that problem.
Oh, the reason I liked the v1 better is because of the way it's filled. it definitely had more things that needed addressed like air flow and such.
Last edited:
I added an oring on the top and bottom of the outside of the plexi tube, it actually looks pretty good!
And I dont have to fear for my tank breaking.
Sent from my SCH-I605 using Tapatalk
And I dont have to fear for my tank breaking.
Sent from my SCH-I605 using Tapatalk
Last edited:
Oh hell maybe I will just go about getting one if it drives my nuts it can collect dust....
Anyone know of a place I can get one at a decent price?
Oh that reminds me too, are their variations of the V2 I see some now have the whole tank part covered in metal with just a few slits in it to show the level of juice. I particularly like that one...
Anyone know of a place I can get one at a decent price?
Oh that reminds me too, are their variations of the V2 I see some now have the whole tank part covered in metal with just a few slits in it to show the level of juice. I particularly like that one...
Afaik that's the official v3 (I guess we'd call it the v4) and it's not available that I know of yet from retailers. The v2/v3 is available several places, fast tech is cheapest but takes half a lifetime to receive...I preferred mine from clouds of vapor, like $35 shipped priority mail if I remember.
Honestly, you're probably better off with the taifun imho. Importvapor.com has them in stock all stainless $75 shipped I think. Again FT has them for cheaper but I can't stand waiting....and it's like 2 months to actually get a package from them.
Remember the Fogger is a inspired by device of the taifun. The taifun looks better to me, and supposedly works better with be less finicky.
Good luck in your search.
ImportVapor.com
Honestly, you're probably better off with the taifun imho. Importvapor.com has them in stock all stainless $75 shipped I think. Again FT has them for cheaper but I can't stand waiting....and it's like 2 months to actually get a package from them.
Remember the Fogger is a inspired by device of the taifun. The taifun looks better to me, and supposedly works better with be less finicky.
Good luck in your search.
ImportVapor.com
Thanks everyone for the replies. Im kinda in the cheap area these days. I cant see spending 75 bucks on a real taifun. You all gotta remember something. I dont think any tank/rba/ect should be upwards of 75-150 dollars. If you ever did machine work you could fly out about 10 of them in an hour. I think its such an up charge on something that doesnt take much time to make or money for that matter.... I even thought a few times of just getting my friend with a machine shop to make me some stuff. I see people buy kayfuns and think, wow you guys are nuts paying that...
I have seen the V3/V4 whatever you want to call it a few places but always out of stock. Maybe they where all pre-sales who knows.
On another note anyone suggest a good Genesis style atomizer? I was thinking maybe the AGA-T2, but seen mixed reviews on it. Im on a cotton rage fest lately. I have seen it done with a cotton wick on the aga. I always liked the idea of the Fogger/kayfun/ whatever you want to call it style. I just cant see paying that much for it. I mean 75 bucks? You can almost buy a nice vv mod for that price...
Fogger V3 is in stock at vapor cigzz for 34.00 BTW That is the one with the metal around the tank...IF anyone was interested.
I have seen the V3/V4 whatever you want to call it a few places but always out of stock. Maybe they where all pre-sales who knows.
On another note anyone suggest a good Genesis style atomizer? I was thinking maybe the AGA-T2, but seen mixed reviews on it. Im on a cotton rage fest lately. I have seen it done with a cotton wick on the aga. I always liked the idea of the Fogger/kayfun/ whatever you want to call it style. I just cant see paying that much for it. I mean 75 bucks? You can almost buy a nice vv mod for that price...
Fogger V3 is in stock at vapor cigzz for 34.00 BTW That is the one with the metal around the tank...IF anyone was interested.
Last edited:
For what it's worth this is a pretty awesome vape for $21:
https://www.fasttech.com/products/0/10006473/1494700-svoemesto-kayfun-v3-1-es-styled-rebuildable
a picture of mine:
So has anyone actually got the fogger working on a consistent basis and been able to replicate their success many times over? I really like the design and look of these and the V2 seems to have addressed many problems of the original like that crap isolator that used to stick up under your coil.
Im particularly interested in cotton builds. I like the taste I get from cotton. Probably wont ever use silica again EVER after using cotton. Id even venture into using ss mesh but again has anyone got this thing running good on a consistent basis? I really wanted to get one of these and I dont mind some minor "tinkering" but I hate stuff that just has to be perfect to work too...
Thanks for your time. This community is great, im 4 1/2 months into my vaping hobby and I love it. I could always use a few more toys in the jouney of finding the ultimate vape!
Yep, here's mine, w/ cotton.
http://www.e-cigarette-forum.com/fo...ogger-v2-best-builds-pics-3.html#post11489129
http://www.e-cigarette-forum.com/fo...ogger-v2-best-builds-pics-3.html#post11489219
- Status
Similar threads
