I'm a little concerned about using my new ProVari on a LR Coil what would you suggest for the lowest I would want to go in Ohms.
Genesis RBA on a ProVari
- Thread starter michaelsil1
- Start date
- th_trl_thread_readers 0
- Status
You can only go so low on the ProVari or it will throw a code. Just use the chart to get you near where you like your vape, you won't necesarilly need to have a low coil to get you where you want to be. That is the beauty of the VV.
http://www.vaporrater.com/images/Safe Vaping Chart.jpg
http://www.vaporrater.com/images/Safe Vaping Chart.jpg
I have two Genesis-style rba's, AGA T2's, that I use on my Provari. I found that I prefer a 2.0 ohm coil, adjusting the voltage to whatever flavors that I am using, not unlike what I do with my cartotanks.
I admittingly prefer a cooler vape as low resistance coils feel harsh on my throat and often mute many flavors. Could be because I had been a menthol smoker for over 30 years. This week marks my 1 year anniversary being smoke free. I'll likely reward myself with a second Provari soon.
I admittingly prefer a cooler vape as low resistance coils feel harsh on my throat and often mute many flavors. Could be because I had been a menthol smoker for over 30 years. This week marks my 1 year anniversary being smoke free. I'll likely reward myself with a second Provari soon.
I have two Genesis-style rba's, AGA T2's, that I use on my Provari. I found that I prefer a 2.0 ohm coil, adjusting the voltage to whatever flavors that I am using, not unlike what I do with my cartotanks.
I admittingly prefer a cooler vape as low resistance coils feel harsh on my throat and often mute many flavors. Could be because I had been a menthol smoker for over 30 years. This week marks my 1 year anniversary being smoke free. I'll likely reward myself with a second Provari soon.
congratulations, I have the AGA-T2 coming this week are you using 32 Gauge?
I use 30 guage, and also coil around 2.0. Then I just adjust the volts up or down depending on how I like my juice. Using about a 2 ohm gives you the ability to adjust to a wider range.
CONGRATS Baditude! Glad to see you finally got away from the tanks
CONGRATS Baditude! Glad to see you finally got away from the tanks
I've fired a coil at 1ohm successfully on my provari. Couldn't go above 3.1volts but it DID work. Usually I prefer a 1.5 ohm coil and somewhere around 3.7v + or -
I'm also using 30g wire, and pre-rolled stainless wicks (from Vapor Kings). I have had some issues with roaming ohms, as much as 1 ohm on both. I suspect it is a coil issue. The pre-rolled wicks work great.
I'm still primarily using my cartotanks after a week of bliss with the AGA's. I'm just more familiar with the cartotanks and they are always consistant and dependable. I've just not had time to mess much with the AGA's lately.
I'm still primarily using my cartotanks after a week of bliss with the AGA's. I'm just more familiar with the cartotanks and they are always consistant and dependable. I've just not had time to mess much with the AGA's lately.
I do around 3/4, and I was mistaken I use 32. Just checked the roll.
With 30g and a 5/6 wrap, I am at 1.8 ohms, using a AGA T2.
- Andy . . . Challenge in lieu of being challenged.
- Andy . . . Challenge in lieu of being challenged.
I got my aga-t2 today it is being cranky and I'm getting a lot errors because of low ohms.
What are you using to build your coil/wick assembly and how many wraps?
- Andy . . . Challenge in lieu of being challenged.
400 SS Mesh wrapped around a paper clip, 32awg 3/4 then 5/6. I found out why I was getting the E1 error Low Ohms because of the spacing of the coils. I'm waiting on some 500 SS Mesh and 30awg. I have it working right now, but I know I wrapped the coils to tight and its not as good as it could be.
Good deal . . . The #500 and 30g Kanthal is what I have settled upon.
I am by no means a RBA veteran, by any stretch of the imagination. I am quite enthusiastic about it though. As such, I have a second AGA T2, which I experiment with and practice making coils/mesh combos.
Much luck and a productive RBA journey to you . . . Enjoy.
- Andy . . . Challenge in lieu of being challenged.
I've been poking and prodding my coils this morning and the Ohms are coming up to where they are supposed to be for the amount of wraps I have and its vaping better.
When I refill my tank, I also perform a dry burn to check the coil. I have noticed that the flavor gets better, as the coil/wick assembly gets seasoned through more use.
- Andy . . . Embrace the day.
Good to know. Do you know where I can buy a syringe locally (CVS,Rite Aid) need to see how my coils are doing.
Your noted places is a good start to look for a syringe. I was shopping on-line at madvapes and purchased a few there. I am using a 14g blunt needle, which works perfectly with the AGA T2.
- Andy . . . Embrace the day.
- Andy . . . Embrace the day.
- Status
