Genisis / Kronos Update

[solarisx]

My package has not shipped yet. I don't want Genesis anymore, and I'm willing to sell it to whoever is interested. Send me a pm if you want it.

 

[Nails]

Just screw the bottle in and than turn a half turn back. If you get leaks into the bottom part it can have two reasons:

- the mesh roll has less than 2,3 mm. In that case to much liquid is going down the mesh. If it is still to much just bend the mesh as shown in the instruction.

- the bottle cap is loose. Some liquids are very agressive and kill the glue. Than liquid will run through the air holes.
Just take the cap out, clean it and glue it in again. clear the air holes with a 1,5mm drill and the mesh hole with a 2,3 mm drill.

Hm, my unglued bottle cap may be the reason for my occasional leaks then. And OK, I might widen that air hole that I left smaller but I like the draw as it is now


@ ArtificialReef - Someone correct me if I'm wrong but 0.9 ohm is too low for some mods to work with.

 

[Tai Pan]

Just use normal fast glue.
I have more than 200 ready made Genisis here and wait for new tops. Another batch of 150 will come end of the week. In about 14 days all should be out. Packing takes some time.

0,9 Ohm is near a short cut. The protection circuit of some protected batteries will switch off than.

 

[kromo]

Any info on where you are in the shipping of the Genisis LVs (ie: what number u are at in the shipping order) I haven't revieved my shipping hotice yet and I am just wondering how much longer I will have to wait... I have been trying my hardest to stop myself from buying other rebuildable attomizers because I ordered this one, hehe, and I am getting ever so excited to get my atty... You have no idea how hard it has been to NOT order other stuff, I keep telling myself that this one is coming and I should wait and see if I like this style atty before buying more.... I can't take it anymore I want great flavor!!

i'm in same stage

 

[mianker]

My Genisis arrived today, looks GREAT, can't wait to make my wick and try it out. Thanks sooooo much.

 

[kcos]

Tai Pan PLEASE word on the Box Kronos

 

[otrem]

got mine today. and vaping now. they're great.

thanks Uwe.(and team)

 

[ArtificialReef]

0,9 Ohm is near a short cut. The protection circuit of some protected batteries will switch off than.

I got it to work once. It is a simple mod and I use the same batteries in the box mod that I have it on now. I think it has to do with the center pin on my roughstack.

Sent from my DROIDX using Tapatalk

 

[BJ43]

I got it to work once. It is a simple mod and I use the same batteries in the box mod that I have it on now. I think it has to do with the center pin on my roughstack.

Sent from my DROIDX using Tapatalk

I think what Tai Pan is trying to tell you is that at .9 ohms even with a 3.7v batt you are doing over 15 watts at 4 amps. This tends to burn juice, burn coils, burn regulators, damage unprotected batteries if not rated for high drain, and disconnect protected batteries even if you got it to work once.

 

[mianker]

Rolled & seasoned my wick, installed and happily vaping. Thanks

 

[vapure_ak]

Rolled & seasoned my wick, installed and happily vaping. Thanks

Pictures or it didn't happen... LOL

 

[Tai Pan]

I have the sample for the box here. It is now with the constructor. I will have it back mid to end of the week. When I have it back I will make some photos. But it is a prototype and only made to check all the measurements. It looks ugly.
Than we are beginning to make the pressure mould next week. The electronic is all with me.

Regarding 0,9 Ohm for the Genisis
That is nearly a short cut. The protected batteries switch of between 4 and 4.2 A. But some do it earlier and than the power is gone. An eGo battery can be killed with that because there the electronic parts are underdimensioned.

 

[ArtificialReef]

Yep, found that one out the hard way. Learning occurred. I am very familiar with electronics but was lacking on the specifics of these batteries. Thanks all for helping me figure that one out. Have to be more careful in the future.

Sent from my DROIDX using Tapatalk

 

[ArtificialReef]

Pictures or it didn't happen... LOL

Ugh, beat me to it.

Sent from my DROIDX using Tapatalk

 

[ainako]

got mine in! followed the directions in rolling wick to a T and it performs better than my g-tank. No dry hits at all using 60pg 40vg juice

 

[Shead]

Hey Tai is there anyway I can get extra bottles with my GLV since it hasn't shipped yet? forgot to add some to the order months ago

 

[otrem]

the bottles are fragile. one was broken during shipping.

 

[Tai Pan]

The bottles are just glass and behave like glass. Who wants more bottles just sends me a mail. Please include your family name. Than I can find you easier.

 

[kcos]

I have the sample for the box here. It is now with the constructor. I will have it back mid to end of the week. When I have it back I will make some photos. But it is a prototype and only made to check all the measurements. It looks ugly.
Than we are beginning to make the pressure mould next week. The electronic is all with me.

Regarding 0,9 Ohm for the Genisis
That is nearly a short cut. The protected batteries switch of between 4 and 4.2 A. But some do it earlier and than the power is gone. An eGo battery can be killed with that because there the electronic parts are underdimensioned.

OK thanks I will be waiting

 

[otrem]

genLv are great. show us yours./..

here's mine..... the ghost