GP Series by VapourArt - Official Thread for GP Spheroid, GP PAPS, X, GP Piccolo, GP SnP and more - Part 3

Status
Not open for further replies.

StrikeIII

Ultra Member
ECF Veteran
Verified Member
Dec 10, 2013
2,063
6,900
Chicago
Thanks :)

I'll post as soon as I know something after my tests on Wednesday.

I also found out that I could get a house loan today, but the payments on the house we were looking at were a little too high for what we could afford. We'll keep looking, but it was a huge bummer. We loved that house. I was also feeling really puny today health-wise. Winning an X really brightened my spirits though :)

Man, house hunting is such a PITA now a days. Good luck Brotha with everything.

Oh, just so you know that while your house hunting all your future vape mail will be redirected to my Chicago office for inspection. [emoji14]

Sent from my HTC One_M8 using Tapatalk
 

newyork13

Vaping Master
ECF Veteran
Verified Member
Nov 9, 2013
4,411
21,209
western Massachusetts
Thanks cliffy. That's what I needed to understand about the tails. I suspect, aside from too much fluff, my tails were too short and the liquid on the deck was spitting rather than getting drawn into the coil and vaporizing. Make sense?

With the Spheroid, I push both the top and the tails up into the tank.

With the Heron, I tuck the tails down into the drip well. That side will wick anything that drips into it when I get impatient and overfill my fluff. =P

I know I posted this previously but here it is again. I don't make my tails quite this long anymore.
abe2asu3.jpg
 

dmska

Ultra Member
ECF Veteran
Verified Member
Mar 9, 2011
1,610
5,139
just coiled up one of the Spheroids. Came out to around .5...add some Boba's.
How the hell can ya'll vape this ....?! Way too hot of a vape for me!
Going back to my happy place around 1.0 :vapor:

My wife used to use dual coil cart's, every now and again I would take a hit. It just tasted awful, way too hot with no flavor. That's how I imagine going lower than an ohm, or dual coils must be.
 

yankeebobo

Vaping Master
ECF Veteran
Verified Member
Jun 23, 2012
7,046
21,034
Western MA
Man, house hunting is such a PITA now a days. Good luck Brotha with everything.

Oh, just so you know that while your house hunting all your future vape mail will be redirected to my Chicago office for inspection. [emoji14]


Sent from my HTC One_M8 using Tapatalk

Of course..... This is what I would do. Redirect to you for safe keeping. :lol:
 

yankeebobo

Vaping Master
ECF Veteran
Verified Member
Jun 23, 2012
7,046
21,034
Western MA
just coiled up one of the Spheroids. Came out to around .5...add some Boba's.
How the hell can ya'll vape this ....?! Way too hot of a vape for me!
Going back to my happy place around 1.0 :vapor:

Bobas at .5. Dial that down to .2 and check your tonsils. :lol:

DISCLAIMER: I'm KIDDING!
 

anavidfan

ECF Guru
ECF Veteran
Verified Member
Jun 14, 2012
10,216
20,329
U.S.
I wanted to send out a "big thank you" to the special someone that sent me some Peaches and Cream yarn so I can try it out. I feel like a real dummy that I dont remember who it was. I cleaned out some of my PMs and I guess I deleted the PMs. It was someone from MI. Thank you so much, I appreciate it. I just boiled it and dried it and I have it in a coil ready to pop in.

Thanks Sandy
 
Last edited:

cliffy15

Ultra Member
ECF Veteran
Verified Member
Apr 9, 2013
1,401
4,396
Honolulu, HI
Hey family... off-topic, I've recently been thinking about getting a dripper... mostly so I can take it out to test e-liquids but if it turns out that I like dripping enough I'm not opposed to keeping it in the rotation. Any suggestions on where to start looking? I'm not new to drippers, but the ones I've had were very cheap (IGO and A7).

I'm basically looking for some price economy since I don't think it will be my primary. Can I get away with something good within the $60-$80 range? Looking for SS in 22mm (something to match my paps v3s) but not ruling out those in 23mm since I may get an X one of these days. Would like adjustable airflow. I'm undecided whether I'll run single or dual coils but want one that can accomodate both with relative ease (not planning on making more than two coils at a time). I do not want a ceramic cup setup.

Preferably no unicorns. =)

TIA!
 
Status
Not open for further replies.

Users who are viewing this thread