Terrific! I'm so glad for you. I have had a few Boge sr's that had the wicking problem. However, most of them seem to be fine.
- Status
LOL... sorry
... I did say "WOW, tough to follow a couple of interesting situations here."
With that aside, I finally ‘drained’ the DIY Iffy Peach flav tri-slot carto/tank to MT on the Buzz Pro. Great vaping ALL the way down. There’s not a full drop left in da tank. Great vape throughout! Now just wonderin’ how long the CCV 510 LR DC carto will provide this truly satisfying vape…
Haven’t MT'd the single slot with the coconut flav yet. But it’s matching the tri-slot performance thus far; most time on an eGo batt. Absolutely no leaks with either combo!
My Iffy’s Peach loves 3.9-4.1 VDC. The coconut does well up to 4.7.
Bought another eight 20ml and six 3ml syringes to experiment with. Got a couple of brain storms (well, would ya believe a light drizzle?) to work on. Which leads to this question, anyone have a measurement for the 1ml plunger disk? TSC didn’t have any…
Really am enjoying the ol' amateur backwoods engineering and hope to add a couple of 'enhancements' in the near future for those interested.
Last edited:
Glad you didn't give up and found what the problem was. Thats funny but frustrating for you. LOL Where did you punch the 2 holes in your carto and then what one did you covered it?
Yes but I have not used it yet, I will fill it tomorrow with a new DC S.S. carto. Just a note, I finally got one made yesterday out of a 10ml syringe and it worked very good but after awhile, I too like another poster had a rubber taste in the vapor and it tasted bad. I use a tobacco flavor and maybe with a cinnamon flavor you might not notice it, but with my fav tobacco juice it tastes bad. Well I made the 20ml syringe with one you sent me and hopefully it won't have the rubber taste. I did clean the first one too with a liquid hand soap before I used it and now I am soaking it in dish soap water and will try it again, but first I will use my new 20ml tank I built today.
Last edited:
They were both right above the bottom seal on opposite sides of the carto.I just cut the condom short and put a hole in one side so that it block one hole while leaving one open. it didnt really matter which one i covered as they were in essentially the same spot just opposite sides.
Thanks, I was wondering about a very few people that have put a second hole toward the top of the carto and I may try that to see what difference it makes, if any.
I've only seen that in reference to CE2 tanks that have essentialy a tube inside a tube that apparantly creates feeding issues if you dont makes holes at the top of the inner tube so that the air can escape to the outer tube. just a disclaimer I've never made a ce2 tank so that could be completely wrong. If you want more info asnider ,who posted early in this thread, has made many of them and has a number of threads in the modding section about them.
Sorry it took a long time to reply, my slit is just above the rubber. Its about 1/16" wide.
I don't vape any tobacco juices. Most of my e liquid is fruit or dessert flavors. I didn't even wash or rinse my syringes. I took them right out of the package, cut them, rinsed them, put them together, and filled them up. So far, I haven't gotten the tiniest bit of rubbery taste.
.
.
Better late than never.LOL I have a dremel so I will try that and see if it works any better than a punched hole. Thanks
ya that picture he posted earlier was from one of his threads but I cant remember which one
Good to know, It maybe the brand of the 10ml syringe I bought.
On my dremel, I put 2 discs together to make the cut. In my opinion, a larger hole works best.
Due to another thread, I took this pic of my Buzz Pro with a 1½" homemade syringe tri-slot carto/tank and an eMDCC rubber whistle tip.
- Status
