That's easy, take a round toothpick, put it in one of the 2 holes on the outside of the 510 connection and cut it flush. This will tighten the draw considerably.
nice trick Lord
Iatty
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
- Status
nice trick Lord
I forgot to send you the Iatty1. Big mistake!!. But I will send you the multiatty for sure Scott
ps....... it will be a very long video Scott, be prepared!
I also forgot the Hifistud (Dave) and his friend (Dave). He will be one of the reviewers too of course. Dave, dont pay attention if I forgot you this time. Its because my mind is always set on GG constructions!
I had to had the nessesary parts yesterday wfa but maybe I will have them on Monday. I will make some tests and I will send the multiatty to the reviewers. So maybe at the end of next week I will ship them.
And dont forget Cat...
Having just reviewed another rebuildable attie, I am now almost an expert....lol, and its been said, by many of my viewers, if Cat can do it, anyone can.... and I can...
Having just reviewed another rebuildable attie, I am now almost an expert....lol, and its been said, by many of my viewers, if Cat can do it, anyone can.... and I can...
ok dear, no problem. But you have to wait a little because I run out of samples right now. I had only 4 and I miss some pieces to make a fifth one. The fifth is for Dave. Yours have to wait until the real batch
cool! thanks imeo.......will very much look forward to trying it out!
Howdy Scott;
I have watched your vids as well and have always appreciated your opinions. I was stationed in England back in 85 for a year and a half and the first thing I did when I got there was to go to a shop and get some fish and chips. I had to see what all the hubbub was about. Wow is all I can say. They made up a cone out of white paper, reminded me of the packing paper used to protect dishes and such and in the bottom went the chips and on top was the cod. First time I ever tried malted vinegar on my chips and or fish.
We walked around town munching on our fish n' chips gawking at everything and trying not to look like tourists. Stuck out like a sore thumb.
Played a lot of war games with the SAS and then afterwards had good fellowship time with them. Shared a meal, told stories, and traded patches, knives and such. Very fond memories there.
Not always bad being a yank there. We were always mindful (at least the group I hung out with) to be on our best behavior while in a foreign country and to leave the "American Ego" stateside. One New Years Eve some of us went up to Edinburgh Scotland and went to a small pub there. I went up to the bar and ordered my usual drink and as soon as the bartender and some of the patrons heard my American accent we were a hit. Free drinks for all the yanks. A few of the ladies there took to us. Guess they thought we were a novelty. ......Ah shucks ma'am.....
That's easy, take a round toothpick, put it in one of the 2 holes on the outside of the 510 connection and cut it flush. This will tighten the draw considerably.
Thanks! Ill try it out!
No problem at all Imeo, you had told me it would be quite some time before you could make them and I know you're busy
I need a cap to finish my second iAtty. I am collecting parts for one for a good friend of mine, I have all parts now except for the top cap, and Bruce is out..
By the way,
Thank you so much for sending an iAtty steel body tube for me with the UFS shipment, it was sent out to me yesterday from Florida.
Very much appreciated!
I have one cap Mosh. I just searched and I found one. So I will keep a note to send it to Bruce for you with the Stealth shipment
Wow Imeo, that's so nice, I sincerely thank you!!
That just made my day, and my friend's day too, he has the worst luck I have ever seen
with atomizers,
now he may never have to use them on on his GGTS again!
That just made my day, and my friend's day too, he has the worst luck I have ever seen
with atomizers,
now he may never have to use them on on his GGTS again!
Hi,
I am trying to pick up an iAtty for some time but they are constantly out of stock. Will there be a new series soon or do i have to wait for the version 2 iAtty? In fact I think I'd buy both but still want an version 1 iAtty
I am trying to pick up an iAtty for some time but they are constantly out of stock. Will there be a new series soon or do i have to wait for the version 2 iAtty? In fact I think I'd buy both but still want an version 1 iAtty
Hi,
I am trying to pick up an iAtty for some time but they are constantly out of stock. Will there be a new series soon or do i have to wait for the version 2 iAtty? In fact I think I'd buy both but still want an version 1 iAtty
Maybe you could build it, collecting all the separate (spares) parts that conform it.
Looks almost impossible to build one from spares as even the spare parts are very rare and basic parts like the central tube aren't available anywhere as far as I can see.
- Status
