Introducing the Precise Industrious RBA

[Riverboat]

Working on emails now, I'm behind a week, hopefully will be caught up by morning

So before I order is it possible to get the Precise Industrious rba in a Satin finish? I don't think I will put it on my ELA Ti as that would take away from the feather light Ti weight.. It is more suited for my ELA V2 Satin.............

 

[INFRNL]

We haven't tried any testing that involves rapid altitude changes. Theoretically, the center Stainless steel wick enclosure itself holds about a 1/4 ml, which should allow it to handle fluctuations in liquid volume due to pressure changes as well as allowing excess to drain back.

Thanks David.

Now to figure out what all I want/need to order...

 

[INFRNL]

just thought of another probable concern; Will this style rba leak if layed over on its side or turned upside down?

 

[forcedfuel50]

just thought of another probable concern; Will this style rba leak if layed over on its side or turned upside down?

I laid it on its side overnight with no leakage, wick was wetter, i just burned it off, but it didn't leak due to the wick and airhole design. Thats not to say its immune to leakage, but its pretty hardy in our testing. I think people are confusing this with a genesis because of the SS mesh used inside the permanent wick, but it isn't a genesis, you don't have the tilt, feed and leak issues of a genesis and the airflow to the coil is much improved and also the SS mesh doesn't get gummed and burned up. The wick design in this feeds from the bottom of the tank and isn't exposed the whole way up.

 

[INFRNL]

I laid it on its side overnight with no leakage, wick was wetter, i just burned it off, but it didn't leak due to the wick and airhole design. Thats not to say its immune to leakage, but its pretty hardy in our testing. I think people are confusing this with a genesis because of the SS mesh used inside the permanent wick, but it isn't a genesis, you don't have the tilt, feed and leak issues of a genesis and the airflow to the coil is much improved and also the SS mesh doesn't get gummed and burned up. The wick design in this feeds from the bottom of the tank and isn't exposed the whole way up.

Thanks for the clarification and info.
Looks like for the moment; I will order a Ti ELA along with the accent rings and industrious for now until you have that sale you mentioned.

I will try to put a comment about smooth Ti lock ring if theres a place. I will also post my order # so you know its me. Thanks again for all the clarification you have provided on all my questions/concerns Going to go place the order now...

Does not look like we can send you pm's. Placed order, hopefully I got it right. Left you a message for the smooth lock ring.

I guess the new system did not recognize my past account, but my new order is #342.

 

[vaptamist]

Nevermind, misread.

 

[HauntedMyst]

I miss coming to the forum for a few weeks and miss this! Seems like an awesome RBA! Nice job!

 

[forcedfuel50]

So before I order is it possible to get the Precise Industrious RBA in a Satin finish? I don't think I will put it on my ELA Ti as that would take away from the feather light Ti weight.. It is more suited for my ELA V2 Satin.............

I never did come across that email. Do you know the order number off hand and we can do satin, no problem.

 

[vaptamist]

Did you get my email? I'd like mine satin - order 312.

 

[Nach]

We haven't tried any testing that involves rapid altitude changes. Theoretically, the center Stainless steel wick enclosure itself holds about a 1/4 ml, which should allow it to handle fluctuations in liquid volume due to pressure changes as well as allowing excess to drain back.

I think the syringe hole would release any air pressure and keep things just as fine as a genesis would.

Also, none of the genesis tilting should be needed with this design, for the user who commented on that.

 

[Nach]

I never did come across that email. Do you know the order number off hand and we can do satin, no problem.

I too would like to get mine with satin to go on my only satin ELA. Order #316

 

[forcedfuel50]

For those who think it may be "limited", heres a couple of more coil builds that we are finding really rock:

Twisted 26ga Kanthal. .5ohm Vaped this one yesterday and love it. Super easy to build:

 

[forcedfuel50]

Dual Macro Coils, the coils spread apart quite a bit putting them on, so its a big fugly, but I've been vaping this the past hour and it is sweet! Tons of Vapor and nice flavor. 26 gauge 4 wraps about .75ohm:

 

[snork]

Oh! I see where the small fill/pressure hole is in that picture - in the tank cap, which is sealed under the top cap. Fantastic! When you mentioned the hole all I could picture is a hole in the side, thought surely not.

A favor please (I'll send an email also): Could you hold shipping for order #313 until after January 1st? It may have just gone out today, if so, no biggie. But if it's still in your hands hang on to it please.

 

[ragnarokstar]

I have shipping notification. I may get this by Christmas.

 

[forcedfuel50]

I have shipping notification. I may get this by Christmas.

Going out today, should see them Monday or Tuesday! Vape the whole Christmas through

 

[Killjoy1]

I missed the announcement, stumbled on this by accident today and couldn't hit the order button fast enough. Glad there were some left Looking forward to putting this beast through its paces

 

[forcedfuel50]

Going out today, should see them Monday or Tuesday! Vape the whole Christmas through

Just an update that I dropped them off at the PO last night about 555pm, online it said that last pickup was 600pm, but the box itself said last pickup was 5:15pm and I checked some tracking numbers and they haven't updated, so it looks like you'll be getting them on Christmas Eve day.

 

[Corona Doble]

Ordered mine today, very interested by the concept. Airflow, sealed tank capacity, finish (this .typical both fine and rugged industrial american design touch, previously appreciated on some drippers) but the way of building is the main interest for me. Last argument to go for an ELA 'too' to drive it.

While very different of the IN'AX and Mojo OMG / LMB , i both already use, this end of 2014 is definitly 'central'

 

[ragnarokstar]

I had a interesting thought, is it possible to make a top cap for the 26650 that would hybrid with the industrious or strata?