iTaste MVP - The good, the bad, and the ugly. Give it to me.

[MaxximumVapo]

i love mine - i bought it just for work for the flatter form factor in my pocket. i got the v2 with the ego threads. it wont fire and kanger t3 but it will fire an evod which is awasome. i use it with an evod or i use it with the 3ml J-tank and the killer705 rebuildable atty that fits in a carto tank. its awasome. i love that fact that if i forget to charge my phone the night before i just plug it into my phone and let it charge in the back for an hour.

the only thing i dont like is the little wobble from the on/off switch on the bottom BUT u can easily fix this. watch FieldOfvapor's review on the MVP on youtube. he shows you how to fix this so it will sit flat.

I am very happy with my choice on a rugged bang around mod to use @ work. I had a VERY close encounter dropping my provari in the bathroom at work while vaping...nearly missing the toliet... that was the end of provari at work at the day i ordered the MVP. Works great

 

[Merlin21]

Picked one up and Vapefest, I have a few twists and a Vamo. Hands down this is going to be my daily driver. However, I use Kanger T'2s and love them but while they fit on the MVP like a glove they do not fire.... Have to add an adapter and the beauty ring. I tried wiggling the T2 connector out a little and ummmm...... destroyed the T2.....

 

[moshiri94]

So in conclusion... Venting or no venting?

Sent from my SAMSUNG-SGH-I747 using Tapatalk 4 Beta

 

[peterforpats]

I will say it is heavier than I thought- that could be a plus or minus depending on what you are looking for. I gave mine to my wife because I don't like the position of the fire/power button. when I grab a box mod I want the fire on the end piece not on the middle of the wide flat section. just too uncomfortable for me to hold for any length of time-would be easier to use my thumb without having to constantly reposition it. also wish it had vw and an ohm checker. oh well, the wife is happy so I am happy. I think it has a way to vent around (or through) the usb port and the batteries it uses are less likely to have heat and explosive problems like cellphone batteries.

 

[F0ur2o]

Could also vent around the LCD screen.

My connection at the top is a press fit and can be moved.

It's not airtight so does it need venting?

 

[Baditude]

I won an Innokin iTaste MVP in a promotional raffle giveaway. The Innokin iClear 16 clearomizers work surprisingly well (not a fan of top-coil clearomizers generally), however I have not been able to use my IBTanked cartotanks on the MVP, either with or without the beauty ring adaptor.

I suspect the center pin connector is not making contact with the cartomizer pin to make the electrical connection. I've read of two other MVP owners who have had the same problem of not being able to use their cartotanks. I could possibly gently tease the pin up higher, but my concern would be would this affect the ability to use the iClears? I plan to donate the MVP to a potential new vapor who likely will use clearomizers exclusively, and I don't want to mess that up.

 

[DavidOck]

Shouldn't affect it at all, Bad. I've some toppers that didn't make the connection, and between wiggling them down and the MVP up, now are fine. Of course, a mm or less is all you want, so be gentle

Not sure how you could prevent it from working with clearos by moving it up. The user just has to snug them up - and if they get over zealous, well, it will just push it back down.

 

[CrimsonJack]

I use Protanks and T3's on mine. The T3's have all been fine, one of my Protanks I have to be careful not to over-tighten, or instead of firing I just get a solid green light for a few seconds with no fire. Other than that oh so very minor thing, and the puff counter (I have no use for this), I freakin' LOVE this thing. Seriously.

 

[DavidOck]

I use the puff counter as a rough estimate of when it's time to charge. I'd rather not wait for the light to tell me, since I might want it ready to go in the AM. Then just power cycle it after charging.

 

[jackiejunque]

I'm late to the party but I have issues with my MVP. I got mine from Fasttech and its already gone back once for the same problem. It works and charges fine the first time, but for the next charge it won't charge. The light flashes red yellow green green green and then repeats withut ever charging. Anyone else have this problem? and if so did you get it fixed somehow?

Jackie

 

[Koman]

I use the puff counter as a rough estimate of when it's time to charge. I'd rather not wait for the light to tell me, since I might want it ready to go in the AM. Then just power cycle it after charging.

I do this, too!

 

[sunnyx]

my MVP isn't fairing too well I can't charge it for more than 30min or it gets too hot and the button disappeared on me. and its past warranty but i loved it when i first got it haha