thankssss lorderos33, poc updated on the uk forum that he maybe shipping some out tomorrow, i just don't know if i am on that list. Thanks for getting back to me
Katana by POC ~ Show and Tell :)
- Thread starter UA72Riddle
- Start date
- th_trl_thread_readers 0
- Status
No problem Armen
I just got on the list that riel created and try one when it's ready.
@lorderos do you know if we can just slide the tank tube and change it out like that or?
The easy way to tell is if you have first threads, they are almost completely flush with the tank. If you have a second or third run Katana then the threads are completely past the outside edge of the tank.
No problem Armen
I just got on the list that riel created and try one when it's ready.
@lorderos do you know if we can just slide the tank tube and change it out like that or?
The tanks are fairly easy to change, you just have to be VERY careful putting the top part of the tank back on. The shorter post can get pushed through the bottom of the tank. It does not break the Katana but can result in a leak.
lorderos - so 2nd run (I guess me?) and 3rd are the same threading? Great!
Riel - guess my threads would be the same as yours.
Riel - guess my threads would be the same as yours.
lorderos - so 2nd run (I guess me?) and 3rd are the same threading? Great!
Riel - guess my threads would be the same as yours.
They should be exactly the same
Lorderos - I have been using my Kat for a couple of days, haven't really taken the cap off much, and just took it off to refill tank ..... it looks like my wick has mutated onto my tall post! It looks like a huge big black glop! 
I freaked out, dry burned it and hit it with the water-pick ..... now it seems fine, but in the future, is that Ok? Or should I keep the build-up down to a minimum?
I freaked out, dry burned it and hit it with the water-pick ..... now it seems fine, but in the future, is that Ok? Or should I keep the build-up down to a minimum?
I have noticed a lot of buildup on the main screw.
I tried to clean it with alcohol, but it did not work.
I tried to clean it with alcohol, but it did not work.
If possible...running a coil with a little more heat (one less wrap or so) reduces the buildup. It takes about a month for me to really see anything on mine, and I know Lorderros is about the same. But we both run really hot coils...around 1 ohm...lol
I just made a new coil, didn't take long, with 3 wraps .... looks like 3 from both sides
Anyway, alot better vapor for now, on 80% VG juice, also used mesh cut a little narrower, so not as thick a roll.
Anyway, alot better vapor for now, on 80% VG juice, also used mesh cut a little narrower, so not as thick a roll.
awesome!! I am looking into making a version that will work for the older models.
HAHAHAHAHAHA
I was just getting ready to post that you will be getting your notification today
I just made a new coil, didn't take long, with 3 wraps .... looks like 3 from both sides
Anyway, alot better vapor for now, on 80% VG juice, also used mesh cut a little narrower, so not as thick a roll.
Look at you go, you're getting to be a Katana pro now. Told you it wasn't going to be that bad, just a little time and patience.
The short one or the tall one. I get some buildup on the tall one from time to time. I just clean it off with a scotchbrite pad when it needs it.
Careful with the alcohol. Isopropyl (rubbing) alcoholism what cracked my plexy.
lorderos or anyone - so I don't keep saying "tall thingee" and "the short guy" ...... Is the tall post the pos or neg one?
I will assume the short one is the opposite ....
I will assume the short one is the opposite ....
- Status
Similar threads
- Locked
