Katana by POC ~ Show and Tell :)
- Thread starter UA72Riddle
- Start date
- th_trl_thread_readers 0
- Status
Now that is a big smiley that's what I look like when I got the katana working how I like it lol
Sent from my SPH-D700 using Tapatalk 2
No wonder I didn't hear from you today, lol.
I would still like to meet up and take notes from you one day . I didn't realize it was gona be so easy . Actualy your post on here are what got me through the setup thanks bud
Sent from my SPH-D700 using Tapatalk 2
No worries
We can meet up one of these days. I'm glad you were able to get everything going One more happy member of Club Katana 
No worries
I would like to be part of that class too
.
Think this got lost in the mix. Generally this warrants a new wick. You can keep that wick for if/when you switch back, though. Otherwise you just remove the juice and flush it out with water and let it dry out.
It's a bit of a pain to switch juice in any tank unless you have multiple tanks, though. In the case of built-in tanks, this would be multiple Katanas. If you change juice hourly, this probably isn't the best mod for it.
I generally just have multiple mods floating around... Boba's in the ProVari, Copper Creek house blend in the GGTS, and BWB Casablanca in the Katana.
I just change juice by sucking out the old and putting in the new .... I usually go down the center of the wick. Less mess.
Does anyone remember what size folks have been drilling their fill holes to?
Does anyone remember what size folks have been drilling their fill holes to?
Blu I drilled mine with a 5/64 drill bit . I use 100% vg and it helped with wicking
Sent from my SPH-D700 using Tapatalk 2
Thanks Brian ... I am gonna go drill mine also ...
Ok, got a few bits of plastic in my juice now, but what the hay.
Brian, how hard was it to get the top off? I was thinking of doing that to move the white plate so my air hole lines up right ...
Ok, got a few bits of plastic in my juice now, but what the hay.
Brian, how hard was it to get the top off? I was thinking of doing that to move the white plate so my air hole lines up right ...
Last edited:
Never mind ... got cap off, rotated white plate so now vent hole in cap is in front of the wick, and drilled fill hole .... Had to take my good wick off, and put it back on, didn't want to, but now we will be all set.
Never mind ... got cap off, rotated white plate so now vent hole in cap is in front of the wick, and drilled fill hole .... Had to take my good wick off, and put it back on, didn't want to, but now we will be all set.
Good deal, most of the V2 Katanas need to have this done. As you can see it is not too hard to do at all
I would like to be part of that class too
No problem
Some weekend we should meet up somewhere, there are a few of us near each other. Paradisevape, brian272465, you me and a few others.
lorderos, it was easier than I thought it would be .... I was sweating a bit though putting the top back on. I remember you saying to be careful of the posts.
Oh, good point Island Vapor .... isn't there just a V1 and a V2, that was done in 2 runs? The last 2 runs of Kats are exactly the same, right?
Island, I believe the threads on the V1 differ from the V2, but Lorderos would know all the other details.
Island, I believe the threads on the V1 differ from the V2, but Lorderos would know all the other details.
Lorderos - geesh ... I was sitting looking at the spread sheet for the tanks waiting for more info ... just saw the co-op thread. 
All taken care of .... sorry for any delay.
All taken care of .... sorry for any delay.
LOL..I was gong to send that if you did not today...I figured you were "lost": LMAOLorderos - geesh ... I was sitting looking at the spread sheet for the tanks waiting for more info ... just saw the co-op thread.
I was ... I don't remember see the "Co-op" thing to the new thread .... just the spreadsheet. Sometimes I wonder about myself .... and don't say anything! 
- Status
Similar threads
- Locked
