- Status
U might have rolled the cotton into a tight wick. Try removing some shreds and it should be fine.
There are a few places you could look..
Cloud9Vaping
Intaste.de
There's a couple more, plus the classies are always available as well. Last I checked, they were sold out.
none that i am aware of. Intaste and cloud9 are the best place to receive LITES from. I have 3, all arrived from Intaste. There was a cali vendor selling the LITE, high priced & no xtra's, IE o-rings and screw driver. I would only trust Intaste & Cloud9, you will receive device and xtra's. Hope Modesto is not to hot today, i used to live in Delhi. Swimming in the canals was fun times.
I have had my klite for about a month and it was certainly a game changer. I exclusively ran 2mm silica super 8 builds with 28g kanthal @ .9-1.1 ohms until last night. Last night I got adventurous and built my first micro coil on a toothpick with the 28g. 9 wraps gave me a 1 ohm coil and I pulled some cotton ball through it and trimmed it down to the suggested length. I was reluctant to try a new build because the super 8 was performing spectacularly. All I can say is, I'm doing everything Vapedivrr does in the future. This is truly outstanding. My advice to anyone would be to run this build. I dont know if I had some beginner's luck or if this really is the easiest build ever. I found that torched 28g kanthal wraps with considerable ease around a toothpick--Way easier than wrapping through the loops of an 8. Juice feed is flawless. Ive tried to make the coil dry out by chain vaping till I was damn near sick and I cant get a less than fully saturated hit. Thanks to all you Kayfun lite pioneers for sharing your knowledge. Cotton and micro coils forever!!!
Thanks cross! The price isn't bad anyway without coupon. I will just order while they have them! Not hot today, only low 90's. I am from Patterson originally, been in Modesto for 2 yrs now, but I work in Tracy. Nice to meet you.
And yes, I did swim in a canal a time or two when I was a kid. Not safe, I know, but when its way over a hundred degrees and you don't have a pool, what do you do?!
Is there a chance the coil changed position (check height) when the wick was replaced?
Jump in a canal.. If this is your 1st LITE i would look back in this thread for Vapedivrr's video on setting up a micro coil. My 1st build was good with silica & 32g kenthal. But the micro coil + cotton (balls) is awesome, simple & cheap.If you are going to vape pluid or grenada, some fluids will swell the upper o-ring. After 2 days all your fluid will run out the air intake. I found a fix, I am using a kanger protank coil seal, replacing the upper o-ring. Perfect this past week, no more swollen o-ring = leak. Same as my ODY's. That upper o-ring sure is important.
My KFL was scheduled to be delivered this morning, but it seems to be stuck in Köln 
Scheduled delivery is now "N/A"
Quite odd.
Scheduled delivery is now "N/A"Quite odd.
Don't think so, I have since returned and replaced with yet another wick, and it's still the same. Im getting vapor but hardly any flavor. The VC I'm using has full flavor/vapor, so I'm not sure what I could have done.
Thanks for your advice crss! I have pool now, so no more canal's for me! Yes this will be my first lite, I will check out that video, sounds like a good setup. Thanks!
Before you changed it (when it was good), was the cotton used the same as what you replaced it with? Thinking maybe different brand balls have maybe different wicking capabilities?
Another possibility is if you did a dry burn on the coils prior to the new wick there's a chance the stuff you burned off may have been the reason for a stronger flavor. Just guessing now. LOL
Lol yea same cotton; I have a 400cnt bag. Yea it weird, I tore the wick off, and tried another wick with the legs of the wick running across the channels, and that's when I noticed a change in flavor. Couple hours later, changed wicks and went back the other way with the legs of the wick just touching the base right above the juice channels, and still muted flavor. I am thinking about just rebuilding the whole thing, coil, wick
- Status
Similar threads
