I get them from Wizard as well as bottles that you can hook the needle to also. These come with a stopper also. Now sharpened ones are a bit harder to come by but just got some from smoktek.
- Status
I get them from Wizard as well as bottles that you can hook the needle to also. These come with a stopper also. Now sharpened ones are a bit harder to come by but just got some from smoktek.
Does anyone know if the new KFL+ v2 can handle higher wattage vaping now or is it pretty much just a minor aesthetic changes.
This is off topic but how u like the nexus 5? I have the nexus 4 and HTC one Google play edition. Wondering if the 5 is worth the upgrade or just wait till soemthing else comes along
Vapure, or most vape shops
With my KFL upside down I press the tip of a standard tipped plastic juice bottle into the fill hole firmly and squeeze, just keep an eye on the air bubble so you know when it's full.
Last edited:
I see them in every vape shop ive been to in san diego. The 3 shops on convoy all have them as well as vapure.
Love it. Had it since November and no lag still. Upgraded from a gs3 n after a while my gs3 would lag from apps.
Sent from my Nexus 5 using Tapatalk
Thanks, I just picked up a needle bottle from Orbit.
If you have a HTC One GPE, there's no point in upgrading to a N5, the specs aren't very different and the HTC One still beats out the N5 in build quality, speakers, and screen quality.
Plus the Z2 and HTC One 2014 are right around the corner, I'm selling my N5 for one of those since I want better battery life and camera.
Anyone notice a more muted flavor with the AFC screw completely off?
Sent from my Nexus 5 using Tapatalk
Sent from my Nexus 5 using Tapatalk
Hi, just ordered the v2.
By the way everyone mispronounces Kayfun and Svoemesto : ]
Svoemesto - sva-yo-mes-to (not svo-mesto)
Kayfun - kai-foon (not kay-fun)
I am Russian 100%. ; ]
By the way everyone mispronounces Kayfun and Svoemesto : ]
Svoemesto - sva-yo-mes-to (not svo-mesto)
Kayfun - kai-foon (not kay-fun)
I am Russian 100%. ; ]
Last edited:
Well, if people learned to spell how things are pronounced, it would make it a heck of a lot easier, no?!
Just kidding.. a lot of stuff does get lost in translation. Trust me, I know!
I am Indian/Canadian.. umm 50/50%
I posted this in another thread, but since this long thread is all about Kayfuns, I guess it is important for this thread too ...
_________________________________
I have not used this Kayfun Lite clone yet since I still have not installed a coil on it.
However, this morning I decided to remove the 'center pin' (or whatever it's called) out of it. This is nylon you see in the side hole of the pin.
I wonder how common this is with these clones? I guess this would restrict airflow to the coil?
(I know this part don't look like anything that came out of an atomizer, but it is an extreme close-up):
_________________________________
I have not used this Kayfun Lite clone yet since I still have not installed a coil on it.
However, this morning I decided to remove the 'center pin' (or whatever it's called) out of it. This is nylon you see in the side hole of the pin.
I wonder how common this is with these clones? I guess this would restrict airflow to the coil?
(I know this part don't look like anything that came out of an atomizer, but it is an extreme close-up):
I haven't seen this in any of my KFL's or the +V2. I wonder if it's a shaving of the delrin insulator that is in the center pin channel.
It's shaving it alright, no doubt about it ... The insulator in the center pin (looks to be made of nylon) is that same opaque white color.
After using the 800 grit wet / dry sandpaper on that center pin, the rough edge of the hole in the side of the pin is now gone (no more shaving of nylon) ... Also, it slides in a little easier now too.
Good to see those last post. I've got 2 KFL+ in transit. Something to be aware of.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
I posted this in another thread, but since this long thread is all about Kayfuns, I guess it is important for this thread too ...
_________________________________
I have not used this Kayfun Lite clone yet since I still have not installed a coil on it.
However, this morning I decided to remove the 'center pin' (or whatever it's called) out of it. This is nylon you see in the side hole of the pin.
I wonder how common this is with these clones? I guess this would restrict airflow to the coil?
(I know this part don't look like anything that came out of an atomizer, but it is an extreme close-up):
This happened with my EHPRO KFL+ and it caused major leaking and flooding issues for a week and an overall shabby vaping experience until I unscrewed the center pin due to the suggestion of a local vape shop. Must have lost at least 6mls of juice. Vapes great now but it was a gigantic headache before.
Last edited:
Whenever I receive a new atty, or mechanical, I completely disassemble it, and run it through my ultrasonic cleaner with a few drops of dishwashing liquid...a quick rinse, and let dry. Gets rid of any gunk left over from manufacturing, and let's me fully inspect it.
Finally got around to creating a video for my Mesh + Cotton build for Kayfuns. It's still uploading but you should be able to catch it here when it's done.
Mesh + Cotton Build for Kayfuns - YouTube
Mesh + Cotton Build for Kayfuns - YouTube
Good idea. Another thing I do is to run a 510 die across the threads of the connector. Don't have to do it with Kayfuns or other high-quality machined devices (there are few of those) but most of the Chinese stuff benefits from cleaning up the threads out of the box. People do not realize how poorly machined they are and they have a destructive impact on mods and mechs. I can twist it on and off by hand...no die-holding tool is required.
http://www.amazon.com/Metric-Right-...TF8&qid=1393359154&sr=8-1&keywords=M7+0.5+die
- Status
Similar threads
