I bought more attys this weekend and figured since I have a kfl 2 kfl+ and a russian I'd get rid of one lol
Sent from my Nexus 5 using Tapatalk
Sent from my Nexus 5 using Tapatalk
- Status
Woody7781, how much juice can you get in the nano?? I am still waiting for SOV to respond to my chimney question.
SOV nano glass kit, ceramic coated Nemesis, custom Delrin top cap
[QUOT E=crss;12689175]Woody7781, how much juice can you get in the nano?? I am still waiting for SOV to respond to my chimney question.[/QUOTE]
Eh, didn't measure. Wild guess I would say around 2.5-3 mls maybe.
And that's with the extra juice well in the top cap.
Eh, didn't measure. Wild guess I would say around 2.5-3 mls maybe.
And that's with the extra juice well in the top cap.
Hmm............My Nano kit cut me to 1.4ml
Well I have that top cap with a pocket in it so I squeeze a little more in it.
Got my new KF Lite Plus Today, installed a micro coil, and when I tested resistance I get zero. If I loosen the center pin I get a reading (1.8, which I was shooting for) but the coil heads are now too loose! Anyone run into this? 
Yehhhhh. Kfl+ doesn't really have a true adjustable 510 connection. I would definitely say that you would wanna keep that pin screwed on tight. The last thing you want is to have the negative post swiveling and touching the positive post and get a short.
Check the 510 connection on your mod. There's a chance that it's been depressed a little too far down from you screwing on the other Attys.
So. Tighten back your 510 connection on your kfl. Try pulling up your mod's 510 connection.
Burping out loud using Tapatalk
Check the 510 connection on your mod. There's a chance that it's been depressed a little too far down from you screwing on the other Attys.
So. Tighten back your 510 connection on your kfl. Try pulling up your mod's 510 connection.
Burping out loud using Tapatalk
Sounds like a dead short somewhere.... how about the insulator under the pos block? Is that OK? Also the insulator on the base? Seems to do it when you have the center screw tight and hence maybe making contact where it should not.
Do you have any pics?
Do you have any pics?
Sounds like your insulator is bad. Take it apart n inspect. You can cut a quick replacement from a credit card.Got my new KF Lite Plus Today, installed a micro coil, and when I tested resistance I get zero. If I loosen the center pin I get a reading (1.8, which I was shooting for) but the coil heads are now too loose! Anyone run into this?
That's not it. I get the same zero connection on my ohm meter and a brand new provari (got the provari and kayfun both today.)
Yikes. Sounds like a bust insulator that sits around the centre post then. That sucks I'm sorry
Burping out loud using Tapatalk
Burping out loud using Tapatalk
What kind of coil is in the kayfun lite? Just thought i might toss the question out.. I went looking at some of your posts, "flux capacitor" made my day.
Kayfun Positive Post Insulators - 5 pack - Kidney Puncher
insulators found here. If you need to back your 510 out, then it makes contact with your device, or ohm reader. Your insulator might be thin. The above site has replacements, or you can try and make your own from a credit card. I do not think you have a "short" just a thin insulator, so your 510 pin is going into the atty to far. I hope this helps & i did not mean to offend with the new ish comment.
insulators found here. If you need to back your 510 out, then it makes contact with your device, or ohm reader. Your insulator might be thin. The above site has replacements, or you can try and make your own from a credit card. I do not think you have a "short" just a thin insulator, so your 510 pin is going into the atty to far. I hope this helps & i did not mean to offend with the new ish comment.
Thanks. I've sent a message to in taste, but I might try the CC trick in the interim. Does it have to have a hole in it?
Are you saying -0- Dead Short?
Coil touching Deck
Positive Block turned touching Negative post riser or insulator damaged. Inspect these areas.
Center Pin Bent and touching Housing.
If this is a Clone with Side AFC - air control screw in to far touching Center pin shaft.
Easy test - Attach to tester and read
If -0- Shorted
Remove coil
Check again
If -0- Short in Kayfun positive path - Positive Block or Center pin/shaft
If -- Open - Coil was shorting.
- Status
Similar threads
