Kayfun LITE

[Bronze]

I have no info of any new version/s of the K'fun dear. All I know is that the K-Mini v2 is in the works.

I hear Dyson is coming out with a new vacuum cleaner. Get that on your list for review too.

Thanks Q.

 

[TheKiwi]

Btw regal if you've tried tightening that sucka up as much as you can and it doesn't work, you're better off opening a ticket with FT and get a new replacement.

 

[ricks]

Should be able to tighten it from the bottom battery contact screw

I have a couple questions.

I baught the fast tech $15/99 special KLF. Not sure which version it is but the fill hole is on the side with a hole cur at a steep slant. One feature I really like is the + and - terminals have holes underneath so you don't have to wrap the coil end under the screw's head, just push the wire thru the hol and the screw is more of a set screw. Any idea of what version that it?

The second question is a problem, the whole positive terminal is loose, the "block swing around the air hole. Is there any way to tighten this up?

Thanks

 

[ethermion]

I have a couple questions.

I baught the fast tech $15/99 special KLF. Not sure which version it is but the fill hole is on the side with a hole cur at a steep slant. One feature I really like is the + and - terminals have holes underneath so you don't have to wrap the coil end under the screw's head, just push the wire thru the hol and the screw is more of a set screw. Any idea of what version that it?

The second question is a problem, the whole positive terminal is loose, the "block swing around the air hole. Is there any way to tighten this up?

Thanks

Really? Ugh.

"I bought a Rolls Royce from Fasttech. I really like the deep dish wheels and the tinted windows. But, the brake pedal is loose and swings around all over the place. Any advice?"

I'll spare you my advice.

 

[vapdivrr]

My usual micro diameters are in the 1.6 to 1.8mm range, last night I tried a bigger coil because I see alot getting away from the smaller sizes. I tried a 2.25mm coil and as usual I place my wick tails down and across the ledge with an angled coil. In the end the flavor was lacking and initially I thought it was the larger coil . What it was is to much material on the lower deck and to close to channels. With my regular diameters, I never have to trim wick tails but as one increases to larger diameters, it seems like one has to reduce the tail amounts. Maybe if one is doing a straight drop wick it doesn't matter as much, but with wicks that run along the ledge it seems that larger diameter coils need some trimming

 

[Fir3b1rd]

My usual micro diameters are in the 1.6 to 1.8mm range, last night I tried a bigger coil because I see alot getting away from the smaller sizes. I tried a 2.25mm coil and as usual I place my wick tails down and across the ledge with an angled coil. In the end the flavor was lacking and initially I thought it was the larger coil . What it was is to much material on the lower deck and to close to channels. With my regular diameters, I never have to trim wick tails but as one increases to larger diameters, it seems like one has to reduce the tail amounts. Maybe if one is doing a straight drop wick it doesn't matter as much, but with wicks that run along the ledge it seems that larger diameter coils need some trimming

Ive always used 2mm coils and you're right all i do is drop the wick until it just touches the base directly next to the channel and its worked flawlessly each time without needing to be trimmed

 

[Agnes Black]

Still a KF noob, but for the last month I've built 1.8 or 2 mm coils and used organic cotton pulled through the coil then nicely trimmed and pushed up against the wall of the deck. If I use a plastic tipped bottle to fill my EhPro KFL +V2 it'll flood. If I use the metal needle nosed bottle or a syringe it won't flood. LOL I'm still in the trial and error part of learning rebuildable atomizers, but if you don't fill the KF a certain way mine floods.

 

[2legsshrt]

I just have one thing to say Vaperev. Love them

 

[JD1]

Still a KF noob, but for the last month I've built 1.8 or 2 mm coils and used organic cotton pulled through the coil then nicely trimmed and pushed up against the wall of the deck. If I use a plastic tipped bottle to fill my EhPro KFL +V2 it'll flood. If I use the metal needle nosed bottle or a syringe it won't flood. LOL I'm still in the trial and error part of learning rebuildable atomizers, but if you don't fill the KF a certain way mine floods.

First, make sure that you have a good seal. Block the air hole and try to give it a little puff. You can quickly tell if it's leaking air or not. I guessing you don't have a seal problem because you'd probably be having flooding issues even when you fill with a needle tip.

A couple of things that I do that I think helps. 1. prime the new wick with a few drops of juice. I think this helps by providing some extra surface tension. 2. I never fill completely full. I use a regular plastic tipped juice bottle and watch the top of the clear section. When the juice goes past the clear, I stop filling. This usually provides a good size air bubble to get me started and wicking seems much smoother that if I fill completely full.

I hope this helps some and happy vaping.

 

[qorax]

All the Fun

3 x Kayfuns and 3 x Russians!

Arranged and composed by: My daughter

 

[Midniteoyl]

All the Fun

Arranged and composed by: My daughter

Was not gonna ask...

 

[vapdivrr]

All the Fun

3 x Kayfuns and 3 x Russians!

Arranged and composed by: My daughter

Maybe not all the fun but here is my current rotation and right at this moment, they all are performing flawlessly.

 

[vapdivrr]

Ive always used 2mm coils and you're right all i do is drop the wick until it just touches the base directly next to the channel and its worked flawlessly each time without needing to be trimmed

I have always been an angled coil guy arranging my tails across the ledge, doing it this way has always worked awesome for me because of my smaller type coils but with bigger coils this can be problematic. I now see that with bigger coils one either must trim or just go straight down

 

[Fir3b1rd]

I have always been an angled coil guy arranging my tails across the ledge, doing it this way has always worked awesome for me because of my smaller type coils but with bigger coils this can be problematic. I now see that with bigger coils one either must trim or just go straight down

Roger that; it seems to eliminate dry hits altogether. It also makes running dual coil and twisted wire so much easier.
In the spirit of the mod envy you guys have caused lol.
My rotation

The green one is a vaporshark dna30

 

[vapdivrr]

Roger that; it seems to eliminate dry hits altogether. It also makes running dual coil and twisted wire so much easier.
In the spirit of the mod envy you guys have caused lol.
My rotation

The green one is a vaporshark dna30

Nice. I like them all except I would only vape the mvp set up if no one is looking.

 

[Fir3b1rd]

Nice. I like them all except I would only vape the mvp set up if no one is looking.

Lol- the mvp is the most sentimental to me. That one got me off cigs altogether. Not to mention down here thats high class vaping Lmao!

 

[regal55]

Should be able to tighten it from the bottom battery contact screw

Thanks that works.

This really isn't all that bad. I like that it uses set screws to hold the coil. It fills from the side wish I knew which version of KFL it is?

https://www.fasttech.com/p/1662502

 

[Midniteoyl]

Your linked on doesnt have set screws and fills from the bottom.. Wrong link?

Sure you didnt get one of the 3.1's? $21.54 SvoeMesto Kayfun v3.1 ES Styled Rebuildable Atomizer (4.5mL) - stainless steel at FastTech - Worldwide Free Shipping

 

[regal55]

I dont like the set screws on that thing at all. And IMO its ugly

I can't figure out how to fill it up, there seems to be no fill hole.

 

[MechanicalsAndRDAs]

How can I make my EHpro KFL+ V2 hit harder? I have to take like 10 second pulls in order to get the hit that I want.

It's 1.3 ohms micro coil. I'm using a mech mod brass GP PAPS with a VTC5.

Edit: nvm I got it! I just have to suck it harder, damn I cough on every exhale lol [emoji10][emoji189]

Edit: nvm it was only on those two hits [emoji1] I'm open to suggestions [emoji106]