Merlin by Augvape and Roxy
- Thread starter MMW
- Start date
- th_trl_thread_readers 0
-
- Tags
- augvape merlin single coil
- Status
Its nice and tight and can't fall out do to the 510 connection screw at the base. The only thing you have to watch is that it is seated below the lip of the plug on the deck. Don't want it snagging yer wick or perhaps causing a short. But with the coil size I used, it's not coming out without effort and tools on your part. It has been one of the best MTL vapes I've used to date.
If I were going to do a quick fix to reduce the air outlet I would roll up a piece of stainless mesh and shove it in there. Of coarse one would have to have some on hand.
Welcome! It's really not bad most of the time.
I passed on that tape and coil insert restrictor to my buddy.
Yes Jim, just by asking this question you became a troll as well [emoji6](meant sarcastically of course as everyone that has questioned the problem has been called a troll). I suppose I'm at fault for the latest outburst for relaying what I was told about his supposed defect from the designer.
Sent from my LG-H901 using Tapatalk
Last edited:
Where is your coil placed in relation to the posts? What size coil is it? Also what flavor are you using? I have one of my 3 adv's and sadly my main, skittles, that I get zero flavor with rayon at all. Haven't tried with the merlin but have in my skittles boreas tank and my limitless. No issues with the other flavors I make but skittles for some reason.I use the direct to lung vaping method.
So the air control is fully open, and
I run my rayon wick in front of the juice flow holes,
allowing the wick to absorb the juice it needs.
No dry hits, plenty clouds, although the taste is somewhat muted.
Sent from my LG-H901 using Tapatalk
Last edited:
As a MTL tootler, I was pleasantly surprised to find that with the air flow a bit less than 1/4 open and the reducer in place, I am fine with the draw as is. I did try a smaller ID drip tip and that made a big difference as well. Now I just need to find one that looks good on it in black (I know, the tank is already SS, but I sort of like the contrast with a black tip).
I vape exactly the same and the drip tip was way to big for me at first.After vaping it for a few days i love the drip tip,i kind of close my lips a bit over it.If i try my old attys now the drip tip seems way too narrow on them. If this RTA keeps performing like now in the long run then my search for the perfect vape is over.
I have to say I'm very, very happy with this and my Serpent mini for RTAs. Both perform beautifully, and I like the option of one large volume and one small volume tank. No dry hits and no flooding on either and simple to build on (except the Serpent is a liitle fussy with trapping small wire).
I'm assuming you mean the lip of the reducer? I tried a 2mm coil like you did but it wouldn't fit into the bottom of the reducer. It was too big so I tried a 1.5mm coil and that fit in there tight. I haven't taped the bottom of the base yet though but I think I'm still going to get air from the top of the AFC ring.
I hope we aren't going to have to read anymore of this 
about defective Merlin's. I've had about enough of it. No...I've had more than enough of it. It is ruining this thread. Let's put it to bed.
about defective Merlin's. I've had about enough of it. No...I've had more than enough of it. It is ruining this thread. Let's put it to bed.
omg all this trolling from one user for a 16.49 cent atty......
Augvape Merlin rta atomizer-4ML - $16.49
Augvape Merlin rta atomizer-4ML - $16.49
Please read the post above yours. This kind of comment is just stirring the
. I have my mouse hovered over the "report" button. I'm sick of this. 
It's a mech Todd but fused so you have to keep the resistance above .7 which for me hasn't been a problem. 26ga 6 wrap has worked out perfect.
Looks nice with that one.Old school, new school...smooth on a mech.
Sent from my LG-H901 using Tapatalk
- Status
