Merlin by Augvape and Roxy

[juicynoos]

I like the 3mm ones. Might have to try them.

Did you find some 3 mm notch coils with the legs pointing in the right direction already then Ricks? I'd like to get some also.

 

[MMW]

I like the 3mm ones. Might have to try them.

How's it going bud? Everything work out with the bases?

 

[Sirfuji]

So did i, i contacted AugVape immediately i noticed the issue...
This grows tiresome, lets move on.


Says AugVape on the box. Gives their website. Silly me for following the obvious chain of support. Im a maverick like that.


Show me where i said it only applied to me or only to the Merlin....i put in the ticket and was told that they wanted a video of the defect, this came from AugVape. Each supplier has their own warranty requirements obviously. Clearly that is AugVapes. I can read english, fasttech never question that it is a defect, they repeat that AugVape wants proof, how can that not be more clear after several times pointing this out. Im prety sure by now fasttech themselves wouldn't even bother asking for proof because theyve already had many returned due to previous defects like the bad base.

More to the point youre continually attacking me and others for having the gall to return something thats defective, yet you apparently have a few of these yourself, hypocracy much? pot calling kettle much? i guess its hard to troll ones self? But feel free to attack others....

Youre nothing but a bitter troll who probably gets all their kicks from trying to (unsuccessfully) bully people in forums. Im sorry to deny you your superiority fix once again.

And just a tip off, because with trolls like you, the penny never drops, so ill spell it out for you... im sure AugVape is going to be very happy with the trolls here spending 7 pages trolling myself and others with issues, you cant even see how youve taken an issue which could have ended with me posting "i have along 510 pin, it doesnt fit my mods and returning it", and a polite response of "Sorry to hear that" and it being done, and turned into 7 pages of bad looking troll post press for AugVape...let me know when they send you a thank you card. You trolls probably cost them more than the AUD$64 they owe me in refunds (AUD$43 for the tank (things arent cheap to buy in Australia) and AUD$23 to return post it (and things arent cheap to return post either))

btw Still no word from AugVape, well i hope they learn a lesson from this at least. Maybe you trolls will too.

 

[ricks]

Did you find some 3 mm notch coils with the legs pointing in the right direction already then Ricks? I'd like to get some also.

I just ordered these, $4.72 Demon Killer 316L Stainless Steel Notch Coil Resistance Wire for RBA Atomizers (12 Pieces) - 0.2ohm (30W) / w/ rods at FastTech - Worldwide Free Shipping

 

[ricks]

How's it going bud? Everything work out with the bases?

They are better and the black one came with the oval shaped liquid feed holes. I'm going to take one of them apart and see if they can be fixed. I have a base that is useless so it won't matter if I kill it.

 

[mgmrick]

They are better and the black one came with the oval shaped liquid feed holes. I'm going to take one of them apart and see if they can be fixed. I have a base that is useless so it won't matter if I kill it.

Before you take it apart... press it together. Seems they may not be pressed together well enough (read that over there)

 

[dwcraig1]

I just ordered these, $4.72 Demon Killer 316L Stainless Steel Notch Coil Resistance Wire for RBA Atomizers (12 Pieces) - 0.2ohm (30W) / w/ rods at FastTech - Worldwide Free Shipping

I'm waiting till they start making them with SS430, hoping they will anyway.

 

[dwcraig1]

I took my air reducer out and put the notch coil back in. It works quite good in power mode but I can't get it to do well in TC mode.
My Merlin magically returned to rotation as a different animal.

 

[Mactavish]

I took my air reducer out and put the notch coil back in. It works quite good in power mode but I can't get it to do well in TC mode.
My Merlin magically returned to rotation as a different animal.

Been running the same setup, no TC issues for over a week, on the Wimec RX75. I will say I cut through 2 notch coils on my first two installs, over tightening. Those non resistance leads are thin, and can come off the weld, hard to see by eye. Double check those areas.

 

[TrollDragon]

I just ordered these, $4.72 Demon Killer 316L Stainless Steel Notch Coil Resistance Wire for RBA Atomizers (12 Pieces) - 0.2ohm (30W) / w/ rods at FastTech - Worldwide Free Shipping

Nice!
Let us know how they work out.

 

[TrollDragon]

I'm waiting till they start making them with SS430, hoping they will anyway.

You ask too much, SS430's would be perfect!

 

[ricks]

Before you take it apart... press it together. Seems they may not be pressed together well enough (read that over there)

All of mine are tight. No gaps at all. I wonder how many orings are in it??? I will find out tomorrow.

 

[dwcraig1]

Been running the same setup, no TC issues for over a week, on the Wimec RX75. I will say I cut through 2 notch coils on my first two installs, over tightening. Those non resistance leads are thin, and can come off the weld, hard to see by eye. Double check those areas.

I went back at it, it's fine in TC mode now, I may have had it on the wrong setting as I didn't change anything about the build.

 

[disley]

The merlin keeps getting better.
I changed the juice, and I can taste it at last.
Good clouds and a nice smooth vape.

 

[dshuld]

The merlin keeps getting better.
I changed the juice, and I can taste it at last.
Good clouds and a nice smooth vape.

Sorry just replying back. Was it diy watermelon or store bought? Glad you got it going though either way.

Sent from my LG-H901 using Tapatalk

 

[Sirfuji]

Just got confirmation that the SS shipped from Fast-tech, should have it in about a month.

 

[ricks]

What size coil is everyone using in the Merlins? I have not tried smaller ones yet and I'm curious if anyone is getting good flavor with a 2mm coil.

 

[MMW]

3-3.5mm here rick.

 

[Dubminer]

2.5 MM here

 

[dhaiken]

They are better and the black one came with the oval shaped liquid feed holes. I'm going to take one of them apart and see if they can be fixed. I have a base that is useless so it won't matter if I kill it.

I read on another Forum that someone pressed them together tighter w/a couple of socket & a hammer and resolved the problem.
Might be worth trying before disassembling &/or destroying it.