- Status
I'd suggest that you start closer to 10% flavoring then adjust fire accordingly. Also, the drops per ML needs to be adjusted based on what you are dripping from (good for when you are adding multiple flavors).
I was telling another via PM earlier: If you want a general sugar-like sweetness, use ethyl malitol. If you are going for citrus, tart, or tangy flavors, use liquid stevia extract. I use alcohol-free stevia @ 5 drops per 10ml, but it is pretty potent. you may want to start at 3 per 10 and adjust to taste.
I was telling another via PM earlier: If you want a general sugar-like sweetness, use ethyl malitol. If you are going for citrus, tart, or tangy flavors, use liquid stevia extract. I use alcohol-free stevia @ 5 drops per 10ml, but it is pretty potent. you may want to start at 3 per 10 and adjust to taste.
That's the one I have. It makes it sooooo easy to get your ingredients right
Sent from my iPhone using Tapatalk - now Free
Damn chemists & their apps!
They say I'm mad...but I'll show them! I'll show the world!!
Sent from my iPhone using Tapatalk - now Free
I just noticed one of the posts on my rm2 is shorter than the other. Is that normal?
Did you name your rm2 ILean? Yes, that is normal. That is so you can tell the difference between the positive and negative.
So I figured out what was causing my airy draw on the RM2. I mustuv not had a tight seal on the drip tip. I put my own drip top on it with a 1.21ohm coil and some RY4 liquid and a organic cotton wick and now it's hitting like a champ.
Anyone ever dripped on a non wicked micro on an rm2? Wanna try some new flavors of mine and don't wanna load up a new wick each flavor.
I have burned up a few wicks and found just wire coil. That was after the hottest, dryest, burned vapor I had ever tasted! No wickless here!
I switched all my wicks back to silica 3-3.5mm. They seem to be keeping up fine with coils from 0.8 - 1.2 ohm. Threading them through was a little trickier than cotton, dipping the tip in VG was all it took though. I'm gonna run them for a couple days and see where I'm at with them. So far I'm liking the flavor better for some reason. All the coils are micros with either 26 or 28g wire. I've even got a short piece in the RM2, no tail or anything and its doing fine too. I was worried most about that one not keeping up.
On a side note, one of my Grands is going to my buddy this weekend. He's been using a Phoenix atty on a Provari for over a year. He's never seen or heard of one. Just gonna hand it to him filled with his favorite juice and tell him to let me know what he thinks about it in a week or two. Kind of like a blind taste test, no hype or anything. Just a quick run through on how to use it. Anybody want to speculate on the results?
On a side note, one of my Grands is going to my buddy this weekend. He's been using a Phoenix atty on a Provari for over a year. He's never seen or heard of one. Just gonna hand it to him filled with his favorite juice and tell him to let me know what he thinks about it in a week or two. Kind of like a blind taste test, no hype or anything. Just a quick run through on how to use it. Anybody want to speculate on the results?
I use fat 3mm silica too - and i make dual coils running typically at close to 1Ω. Not micros. If i find it is not working just so - it's usually because the squonking is wrong and i remedy that by just removing the bottle and reattaching it a little less tightly. They last me easily a week at a time and the flavour is great.
i don't bother to dry burn and wash them, because that means walking to the sink and messing about and it's faster to just make new ones. I shall be interested to try SXD's latest micro from his (new-ish) video when i have some different resistance wire - i have some ordered to give it a go.
T
I'm gonna have to try one of those. Looks very promising. Glad I didn't cut slits in all my top caps. Have you tried anything similar in a Cyclone?
Have I tried it on a cyclone? It's kinda tough with how small it is and the post setup. I usually run either duals along the sides or a single horizontal or vertical folded in the empty space next to the posi post. Pic incoming
- Status
Similar threads
