Odysseus official
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
-
- Tags
- halo madvapes provari revolution
- Status
the problem is on the inside threads where the rebuildable unit screws in. It starts to screw in, and about halfway it gets really rough and tight and I cant get enough of the center pin to go past the opening so it makes contact to fire.
Like I said the inside of the threads are really rough, and burred. Even the outside is not as smooth and shiny like your usual finish. Inside also you can see scratches like it was scratched up with a screw driver.
All those things I could deal with because things can be buffed out but not being able to seat the rebuildable unit in correctly and the first one being dented on the 510 threads are not fixable for me.
This is a photo of the first base I got, I have to take photos of the second one, but basically the same except the dent on the 510 connection, but rougher threads.
Like I said the inside of the threads are really rough, and burred. Even the outside is not as smooth and shiny like your usual finish. Inside also you can see scratches like it was scratched up with a screw driver.
All those things I could deal with because things can be buffed out but not being able to seat the rebuildable unit in correctly and the first one being dented on the 510 threads are not fixable for me.
This is a photo of the first base I got, I have to take photos of the second one, but basically the same except the dent on the 510 connection, but rougher threads.
Last edited:
Thank you very much for your pics ana my dear and sorry for the trouble. I will talk to vasillis about this and he will contact you as soon as possible
Ive had my odysseus for awhile and just used it for the first time. (been using penelope). anyway it seems I am missing a top oring because my juice pours out of the top once I fill it. If I am missing one where would I get it?
Thanks in advance for any assistance. It seems that orings are never in stock, anyone know a good place to get replacement rings for oddy, penelope, and SSTS?
Thanks in advance for any assistance. It seems that orings are never in stock, anyone know a good place to get replacement rings for oddy, penelope, and SSTS?
It's a 9mm ID x 2mm Cross if that helps. I don't know if anyone local (a hardware store) may have them.
Hey Fanky, if you need one PM me and I get send you one for your Ody.
I found this on amazon
http://www.amazon.com/M2x9-Buna-N-O.../ref=lh_ni_t?ie=UTF8&psc=1&smid=ATVPDKIKX0DER
I found this on amazon
http://www.amazon.com/M2x9-Buna-N-O.../ref=lh_ni_t?ie=UTF8&psc=1&smid=ATVPDKIKX0DER
Last edited:
I try to keep things that are not too expensive in my stash in case of these type of emergencies. I know people have come to my rescue many times. Im so happy to pay it forward in sharing info or parts if I can.
I do as well and it seems my stash is running low. I always advise people to stock up on simple things that fail. Most know parts can be hard to find so when they can find them to buy a couple not a basket full. And while were at it try to replace the piece someone sent to you to replace theirs.
LOL, after I posted that I was thinking, that I might end up giving away things that might become unavailable someday. But heck things like o-rings that I can order on ebay or amazon are no big deal. The next pre-order of Ody parts, Im going to order some back ups of important things. Thats why when I saw the 510 base available I jumped on it. I just wonder if there is even a 510 base instock somewhere to replace the imperfect ones.
They came from a genuine certified GG reseller.
I would even like to see if someone with machine equipment could adjust the inner diameter of the inner threads just a hair so I can screw in the rebuildable part. If someone is gifted Id gladly send the parts in to let them have a go at them.
They came from a genuine certified GG reseller.
I would even like to see if someone with machine equipment could adjust the inner diameter of the inner threads just a hair so I can screw in the rebuildable part. If someone is gifted Id gladly send the parts in to let them have a go at them.
WOW, All I can say is WOW. First let me start off by saying I love GG products. I have been running a Penny for quite a long time now and it has been my primary vape since I got it. I picked up an Ithaka from the classies a little over a month ago and it soon took the spot for my main device, primarily because of capacity and ability to use dual coils. I never really thought about putting duals in my penny because of the size, I didnt think there was enough room for my chubby fingers.
Recently, thanks to Rivernut, I finally got the Ody I have always wanted. I got it mainly to complete the set, with no real intent to have it as my primary. After all, I already had the Beautiful Penny and the hard hitting Ithaka. I figured I would use it as my "test bed" for new juices and the occasional coil experiment.
Well, let me tell you. I started using the ribbon kanthal about a month ago and I really like how easy it is to work with (I use a wire welder). And last night around Midnight I got a wild hair to see if I could run a dual ribbon coil in my Ody. To be honest, I didnt think there would be enough room, but I couldn't sleep anyways so I figured I would give it a shot. After all, I wanted to use this thing for testing. I was not preparred for the result.
Sorry I didnt get before pictures, but I really didnt think it would work this well!!!
1.4 Ohm each, .75 Ohm total on 3.5mm silica at coil, 3mm silica in channels. As soon as I took the first hit I thought "I should take a picture of this" but I couldn't bring myself to tear it down (hence the dark spots on the coil). I have already run a tank through it in the short amount of time it has been up.
Simply Amazing!!!!
Edit: I cant wait for my next rebuild of my Penny, I will take pictures of that one.
Recently, thanks to Rivernut, I finally got the Ody I have always wanted. I got it mainly to complete the set, with no real intent to have it as my primary. After all, I already had the Beautiful Penny and the hard hitting Ithaka. I figured I would use it as my "test bed" for new juices and the occasional coil experiment.
Well, let me tell you. I started using the ribbon kanthal about a month ago and I really like how easy it is to work with (I use a wire welder). And last night around Midnight I got a wild hair to see if I could run a dual ribbon coil in my Ody. To be honest, I didnt think there would be enough room, but I couldn't sleep anyways so I figured I would give it a shot. After all, I wanted to use this thing for testing. I was not preparred for the result.
Sorry I didnt get before pictures, but I really didnt think it would work this well!!!
1.4 Ohm each, .75 Ohm total on 3.5mm silica at coil, 3mm silica in channels. As soon as I took the first hit I thought "I should take a picture of this" but I couldn't bring myself to tear it down (hence the dark spots on the coil). I have already run a tank through it in the short amount of time it has been up.
Simply Amazing!!!!
Edit: I cant wait for my next rebuild of my Penny, I will take pictures of that one.
Last edited:
Hi dark if you need a hand with duals on penny or ody let me know I have some vids on that.
With ribbon or round? I have lost my taste for dealing with round resistance wire.
Yes! Post links Bishop! Who wouldn't want to learn more from the master of the multi coil!
forgetaboutit!
lol sorry, I couldn't resist
forgetaboutit!
lol sorry, I couldn't resist
Just checking to see if you have any updates for me, Imeo. I havent heard from Vasilis. I know he is busy with the new store, but I would like to know if there will be a solution to the 510 bases I have that are faulty.
Thanks
Thanks
vasillis already told me before 3 days that he will send you another base my dear ana. I thought that this issue was solved. Please send him another e-mail if you like.
.Thank you, I hope this one that comes will be fine. Let me know where I can send the defective ones. I would think you would like to see them. Thanks again, looking forward the the good base.
if you can send them back, please send them to vasillis my dear. If you dont want to send them back, no problem at all
- Status
