Odysseus official
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
-
- Tags
- halo madvapes provari revolution
- Status
I agree, My last coil I made I hate to put it this way but.... I think I was not paying attention
...I alway do a great coil
But I got sloppy and cocky at the same time
, Had a reality check...made a new coil ...happy again 
...I alway do a great coilBut I got sloppy and cocky at the same time, Had a reality check...made a new coil ...happy again
So here's my question. I was using a GGTS with a 901 atomizer... Dripping. I now have the odysseus drip mode. I vape at 6v. (2x123's 3v). I always enjoyed this set-up because I could utilize the adjustable draw and was very satisfied with it. I bought the odysseus drip mode. I love it! I got wrapping coils down, and getting my ohms right for my 6v. The problem I'm having: to attach the Odysseus drip mode to my GGTS, I've found I have to use a long 510 to 901 adapter, then a short (comes with GGTS) 901/510 adapter to then get it to attach deep into the collection tank of the GGTS to fit. This extinguishes the ability of the adjustable draw, and I get my draw from the openings around the adapter/bottom cap of the Odysseus. It causes a whistle, and I lose the control I was used to. Am I doing something wrong? I put a stealth cap on my GGTS and then added the Ody, It works, but it still whistles, and I can't adjust my draw... how can I get the best of both worlds? rebuildable atomizer (ody), adjustable draw (GGTS)? I was hoping the two would offer both together...... It's just I feel I get a better hit with a generic atomizer and the adjustable draw over the drip mode and the draw from the openings around the 510/901 adaptor. would love some advice. 
Last edited:
So here's my question. I was using a GGTS with a 901 atomizer... Dripping. I now have the odysseus drip mode. I vape at 6v. (2x123's 3v). I always enjoyed this set-up because I could utilize the adjustable draw and was very satisfied with it. I bought the odysseus drip mode. I love it! I got wrapping coils down, and getting my ohms right for my 6v. The problem I'm having: to attach the Odysseus drip mode to my GGTS, I've found I have to use a long 510 to 901 adapter, then a short (comes with GGTS) 901/510 adapter to then get it to attach deep into the collection tank of the GGTS to fit. This extinguishes the ability of the adjustable draw, and I get my draw from the openings around the adapter/bottom cap of the Odysseus. It causes a whistle, and I lose the control I was used to. Am I doing something wrong? I put a stealth cap on my GGTS and then added the Ody, It works, but it still whistles, and I can't adjust my draw... how can I get the best of both worlds? rebuildable atomizer (ody), adjustable draw (GGTS)? I was hoping the two would offer both together...... It's just I feel I get a better hit with a generic atomizer and the adjustable draw over the drip mode and the draw from the openings around the 510/901 adaptor. would love some advice.
You need this for Adjustable draw with the Ody, but you cant use it with drip mode! You can use your short mode ody as a huge dripper!
http://www.cloudsofvapor.com/store/...y-2-usa-only/1059-new-odysseus-base-ggts.html
So here's my question. I was using a GGTS with a 901 atomizer... Dripping. I now have the odysseus drip mode. I vape at 6v. (2x123's 3v). I always enjoyed this set-up because I could utilize the adjustable draw and was very satisfied with it. I bought the odysseus drip mode. I love it! I got wrapping coils down, and getting my ohms right for my 6v. The problem I'm having: to attach the Odysseus drip mode to my GGTS, I've found I have to use a long 510 to 901 adapter, then a short (comes with GGTS) 901/510 adapter to then get it to attach deep into the collection tank of the GGTS to fit. This extinguishes the ability of the adjustable draw, and I get my draw from the openings around the adapter/bottom cap of the Odysseus. It causes a whistle, and I lose the control I was used to. Am I doing something wrong? I put a stealth cap on my GGTS and then added the Ody, It works, but it still whistles, and I can't adjust my draw... how can I get the best of both worlds? rebuildable atomizer (ody), adjustable draw (GGTS)? I was hoping the two would offer both together...... It's just I feel I get a better hit with a generic atomizer and the adjustable draw over the drip mode and the draw from the openings around the 510/901 adaptor. would love some advice.
A picture would help, but if I understand the issue....you need to eliminate the air supply from everywhere except the collection tank. Then, the adjustable draw will perform like you want it to. Not being able to see the setup, I know if you make an adapter that fits flush with the top of the end cap, then you can utilize the adjustable draw with any device you attach to the GGTS.
Here's an example of the adapter....the slot is where the air comes into the tube and then to the attached device. The adapter fits entirely inside the collection tank.
Here's what it looks like installed.
A picture would help, but if I understand the issue....you need to eliminate the air supply from everywhere except the collection tank. Then, the adjustable draw will perform like you want it to. Not being able to see the setup, I know if you make an adapter that fits flush with the top of the end cap, then you can utilize the adjustable draw with any device you attach to the GGTS.
Here's an example of the adapter....the slot is where the air comes into the tube and then to the attached device. The adapter fits entirely inside the collection tank.
Here's what it looks like installed.
DAM that is sweet! Nice one Para! Hell maybe i had it all wrong with the Ody base. haha
Roseblue, with the setup you describe I have a suggestion that may help. If you have an o-ring that is a suitable thickness try putting that underneath your Ody drip base. This will force all air to come in through the collector tank's air control. It may or may not work depending on your particular adapters
That's it.... I told my wife, I need to block the holes at the top of my adapter. The adapters I have either don't reach far enough to connect into my GGTS collector tank, therefore unusable, or the only other one I have is a cm or two too long, but it has holes at the top (where the Ody drip meets), and that's where the air pulls..... yes, I believe I need an o-ring (901 size) or preferably, an adapter that accepts air below the top of the GGTS right? any suggestions on where to get that awesome adapter pictured above? Love my GGTS, just wanna love my Ody to the hilt as well. Thanks guys!
510 Adapter
This is the thread adapter I'm using.... there are air holes around the top threads... that's where the pull of air is coming from.... I need an adapter without those holes.
This is the thread adapter I'm using.... there are air holes around the top threads... that's where the pull of air is coming from.... I need an adapter without those holes.
Trace where the device is getting it's air, block it off above the GGTS, make sure you have a air feed from the control tank to the device.....and you are all set.
what size o-ring fits a 901? or a 510? I'm afraid to use anything else cuz the heat.
I tried using an o-ring from a drip tip... it fits, but won't stay snug against the bottom of the drip ody base. air still pulls through.... what does everyone else do?
Here's an example of the adapter....the slot is where the air comes into the tube and then to the attached device. The adapter fits entirely inside the collection tank.
Here's what it looks like installed.
Where did you get your adapter? That's EXACTLY what I need! It's just all the ones I find online have the slots at the threads, and yours fixes the issue. Can you remember where you got it? also, what's the length? It looks flush with your GG! Great adapter, I could probably cut the slot myself, but I still can't find an adapter without the air slots. Thanks so much for all your help.
Last edited:
so i had to take my ring off at work today to do some tedious work and i found a ring holder
which if course led to this,
looks much cleaner imo. sort of ties them together. they arent super polished shiny since they are my everyday mod. dont kill me dspin lol
which if course led to this,
looks much cleaner imo. sort of ties them together. they arent super polished shiny since they are my everyday mod. dont kill me dspin lol
so i had to take my ring off at work today to do some tedious work and i found a ring holder
which if course led to this,
looks much cleaner imo. sort of ties them together. they arent super polished shiny since they are my everyday mod. dont kill me dspin lol
I did not read your post first, just peeked at the first photo, saw the "bling" and my first thought was WHY? LOL
Dang you must have huge fingers.....I'm comparing my fingers to my ProVari
Looks really good urquidez
i dont know if this is a normal occurance, but my ody started at 2.8 ohms. beem two weeks and the ohms have been steadily climbing. right now the ohms are at 4.1 that just doesnt make sense to me. i mean 3 ohms id understand but all ths wah to 4 that is weird. is this normal ody behavior?
- Status
