can someone recommend a good meter for my coils? i have "prime" on Amazon so im looking to find one and get it shipped!
Odysseus official
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
-
- Tags
- halo madvapes provari revolution
- Status
Hi jager,
Maybe this could help:
http://www.e-cigarette-forum.com/fo...s-decent-multimeter.html?highlight=multimeter
I just went into a Radio Shack and picked up a nice digital multimeter for $25 and it works great.
LOL got so many replies in that thread I ended up being just confused
I know
And you ended buying one at radioshack, like I did also
After my second attempt, successfully built a coil! Next, to amazon to buy a multimeter. Gotta love the Ody!!
Last edited:
i didnt use any meter to measure the coil. My setup is 5cm of R wire and 4cm of non-R wire x 2. Normal wick.
pls advise
Bro,
May I ask your '5cm of R wire' is what type of wire? Seems to me your R wire is abit too long thus making your total resistance to the higher side. Of coz perhapes gonna have to consider the voltage you vaping at to comfirm.
I'm using 0.16mm Nickel Chrome wire and 3cm of it will give me around 1.8ohm+/- and using it at 3.7v.
The Non-R wire I have it around 9cm so easier for me to tie to the ody body.
May I ask your '5cm of R wire' is what type of wire? Seems to me your R wire is abit too long thus making your total resistance to the higher side. Of coz perhapes gonna have to consider the voltage you vaping at to comfirm.
I'm using 0.16mm Nickel Chrome wire and 3cm of it will give me around 1.8ohm+/- and using it at 3.7v.
The Non-R wire I have it around 9cm so easier for me to tie to the ody body.
thanks for reply bro..
I got 3 type of R wire. 1st R wire from original from Aus side. 2nd R wire is Kanthal-A1. 3rd R wire is Nichrome 34 gage.
I love 3.7v can tell me your setup ?
thanks
Insane bro,
The 1st R wire you mentioned I believed should be a 0.15mm NiChrome this the resistance will be higher even if cut at 3cm.
The 2nd R wire I have not try before so I could not agar the resistance but as for the 3rd R wire, it's similiar to mine. 34 gauge is about 0.16mm.
The thinner the R wire, the higher the resistance will be.
3cm of the R wire gives me around 4 wraps on my wick (I double wick).
My setup is just my Ody(short mode with GGTS base) on my GGTS with a single 18650. That's my daily vape.
Regards
The 1st R wire you mentioned I believed should be a 0.15mm NiChrome this the resistance will be higher even if cut at 3cm.
The 2nd R wire I have not try before so I could not agar the resistance but as for the 3rd R wire, it's similiar to mine. 34 gauge is about 0.16mm.
The thinner the R wire, the higher the resistance will be.
3cm of the R wire gives me around 4 wraps on my wick (I double wick).
My setup is just my Ody(short mode with GGTS base) on my GGTS with a single 18650. That's my daily vape.
Regards
thanks for reply.
do you mean the balance 3cm after the non-R tie together?
cheer.
Before Bro.
After tying/twisting the R and Non-R wire together, Roughly I get about 2cm of the R wire left from the 1st twisted point to the other twisted point.
After tying/twisting the R and Non-R wire together, Roughly I get about 2cm of the R wire left from the 1st twisted point to the other twisted point.
I've modified both my short mode mouthpieces by shortening them about 1.5cm and adding 510 atty sleeves. Here is the result on Ody mid mode and odyufs
I'm having some major leaking issues with my Odysseus in Full mode.
If anyone has some good advice it would be greatly appreciated.
Here's the deal....
Odysseus in Full Mode Leaking alot. - Only leaks through the Center Post Hole (#9 in Wiki Diagram for Full Mode Odysseus)
I put my Ody in full mode. Every single piece, part, O-ring is brand new. I lubricated all the threads (very lightly) lubed all the O-rings (very lightly) and threaded every piece together very carefully 5 separate times. No cross threading, no loose connections, no incorrect, missing or lose O-rings.
I have broken the unit down 5 times, and re assembled it, lost about 8 ML as of now and am becoming extremely frustrated with this.
I have searched for leaking issues with Odysseus, searched the Wikis and found Imeo's video on the non leaking Ody.
Watched it over and over again to see if there was something I missed, but I didn't miss a thing.
Current situation:
Odysseus assembled in Full Mode.
Cleaned, assembled, each time 5 times already.
Replaced the ceramic with a brand new ceramic insert
Used single wick 1.5 wick (3 times) then went to Double wick (2 times)
Verified the Full Mode mouth piece was not cross threaded or bent
Negative and Positive wires from rebuildable atomizer are exactly where they should be and not creating any gaps
Ody in Full Mode mounted to a Odysseus GGTS Base with O-Ring
No fitting is too tight or too loose they are all just right.
I'm leaking an 85PG / 15VG e liquid
Is the liquid too thin? - It has some consistency.
I am extremely disenchanted and not sure what else to do to resolve this issue, not to mention I am almost out of my last throw away e-cig to hold me over until I got this resolved.
I appreciate any and all viable input to resolve.
Thank you in advance.......
Peace-
If anyone has some good advice it would be greatly appreciated.
Here's the deal....
Odysseus in Full Mode Leaking alot. - Only leaks through the Center Post Hole (#9 in Wiki Diagram for Full Mode Odysseus)
I put my Ody in full mode. Every single piece, part, O-ring is brand new. I lubricated all the threads (very lightly) lubed all the O-rings (very lightly) and threaded every piece together very carefully 5 separate times. No cross threading, no loose connections, no incorrect, missing or lose O-rings.
I have broken the unit down 5 times, and re assembled it, lost about 8 ML as of now and am becoming extremely frustrated with this.
I have searched for leaking issues with Odysseus, searched the Wikis and found Imeo's video on the non leaking Ody.
Watched it over and over again to see if there was something I missed, but I didn't miss a thing.
Current situation:
Odysseus assembled in Full Mode.
Cleaned, assembled, each time 5 times already.
Replaced the ceramic with a brand new ceramic insert
Used single wick 1.5 wick (3 times) then went to Double wick (2 times)
Verified the Full Mode mouth piece was not cross threaded or bent
Negative and Positive wires from rebuildable atomizer are exactly where they should be and not creating any gaps
Ody in Full Mode mounted to a Odysseus GGTS Base with O-Ring
No fitting is too tight or too loose they are all just right.
I'm leaking an 85PG / 15VG e liquid
Is the liquid too thin? - It has some consistency.
I am extremely disenchanted and not sure what else to do to resolve this issue, not to mention I am almost out of my last throw away e-cig to hold me over until I got this resolved.
I appreciate any and all viable input to resolve.
Thank you in advance.......
Peace-
- Status
