Dibi, any chance of a sneak pic of one of the mods in progress, just a wood housing or something to whet our appetite? Pleeeeeze?
PDIB's Making MODs!
- Thread starter pdib
- Start date
- th_trl_thread_readers 0
- Status
I . . . . can. . .. . . wait. .. .as anything worth having is worth waiting for.. . . . . .
While you are totally correct, I'm getting very excited to see the mods that are being completed because once they are done, and after his 6 month time off with his family (as stated a few pages back) he'll be starting work on group 2 (which I'm in).
Spent the day trying a few ideas... Among them, the microest micro-gen. Not counting the 510 or drip tip... 17mm...
Still testing... (Deciding)... The size is awesome but a pita to wick & coil.
I tried XC-116 and completely fell apart... It was too short to hold together. The XC-132 did just fine...
It's also kinda cramped up, not much room to work.
I'm thinking a couple extra millimeters may meek a little more friendly.
That said, now that it's set up it's hitting like a dream... Each squank completely covers the coil then drains off, so each hit is dead on.
I'll take some internal shots tomorrow.
I tried XC-116 and completely fell apart... It was too short to hold together. The XC-132 did just fine...
It's also kinda cramped up, not much room to work.
I'm thinking a couple extra millimeters may meek a little more friendly.
That said, now that it's set up it's hitting like a dream... Each squank completely covers the coil then drains off, so each hit is dead on.
I'll take some internal shots tomorrow.
Sorry if this is a dumb question or has been asked already but is the OD repairable by the user? If it is will you be selling a repair kit and extra bottles?
I'm thinking I need to bow out and give another my spot..
pdib is getting stressed with time lines and blocks of pretty sent to him.
He most likely has a nice in house stock. But everyone's so set on sending him their pretty,
I think he may have created a Monster.
I'm just a In stock kind of buyer.
So if it helps I'll give up my spot..
pdib is getting stressed with time lines and blocks of pretty sent to him.
He most likely has a nice in house stock. But everyone's so set on sending him their pretty,
I think he may have created a Monster.
I'm just a In stock kind of buyer.
So if it helps I'll give up my spot..
Last edited:
Mech mods are relatively simple so yes, they're repairable. Either I missed that post or it hasn't been mentioned but I'm sure a DibiKit can be arranged
Last edited:
Spent the day trying a few ideas... Among them, the microest micro-gen. Not counting the 510 or drip tip... 17mm...
Wow... that's pretty good
!!!
I know what this thing can do…
Happy to be on the beta list (b/f MG) once you get it sorted Jas
honestly gang although I'm not a tinkerer… all thumbs and pretty damn well blind too, but for those that like
1. a freakin awesome already setup rba +1
2. like to tinker with micro tools (tiniest bolt and nuts i've ever seen), this is one kick azzzz rba-tomizer!
Since the wick is a weave nextel type or even mesh its going to last and will take a ton of rinse n burn cleanings before even needing to change out a coil or wick.
I have a couple of these so does MrDibs
This is not a cotton puff wick… but the flavor and vape is superb. i like 'em around .6 ohms (i'd want it started at .4 or. 5 to allow for the inevitable resistance going up once its broken in … ymmv.
I wouldn't worry so much about the profile (height) so much as the vape-values man… (hell I started out with a Reo and a put 901's on it for a couple years).
Happy to be on the beta list (b/f MG) once you get it sorted Jas
honestly gang although I'm not a tinkerer… all thumbs and pretty damn well blind too, but for those that like
1. a freakin awesome already setup rba +1
2. like to tinker with micro tools (tiniest bolt and nuts i've ever seen), this is one kick azzzz rba-tomizer!
Since the wick is a weave nextel type or even mesh its going to last and will take a ton of rinse n burn cleanings before even needing to change out a coil or wick.
I have a couple of these so does MrDibs
This is not a cotton puff wick… but the flavor and vape is superb. i like 'em around .6 ohms (i'd want it started at .4 or. 5 to allow for the inevitable resistance going up once its broken in … ymmv.
I wouldn't worry so much about the profile (height) so much as the vape-values man… (hell I started out with a Reo and a put 901's on it for a couple years).
Spent the day trying a few ideas… Among them, the microest micro-gen. Not counting the 510 or drip tip... 17mm...
Last edited:
I think everybody just slides up one slot. I'll miss you when I jump to group 4, but not enough to stay.
hey, loli. good question. I've been thinking a lot about that, all through the design process. The simple answer is yes. I haven't communicated much of that information yet; but plan to have a "technical thread" running by the time anyone might need it. The whole mod is built to be easily accessible for cleaning, maintenance, repair. Most parts are readily available and can even be substituted with similar items. Although some of the operations involved may require a deft touch, this mod is intended to be supremely modifiable and hackable. It's the backyard mechanic's dream vape machine. I will be happy to supply any replacement parts needed, and I intend to provide some simple tutorials in the tech thread. All that coming soon.
Last edited:
uh oh..........
but, no. i'm not giving up my place (s) in the Q
what's more, you can always send it in for a little TLC in pdib's workshop
- Status
Similar threads
