Penelope V2

[Sad Society]

V2 is excellent since I fixed it. I had to lower the power from 8 watts to 7.

Also, to be a bit off topic. I use cotton for my wicks. I found that if you let the cotton soak in ejuice for a couple of days before use, the cotton lasts much longer.

I like cut the cotton wick to size fit the V2, then slide into coil and soak in ejuice for a day or two before using.

 

[Samkinra]

Any pictures to show how to do microcoil on penelope or Ody v2?

I always screw up or end up 3-5 ohms - using 30awg...

Any affordable wire welder recommend?

Thanks in advance


Sent from my iPad using Tapatalk HD

 

[blackwater]

Any pictures to show how to do microcoil on penelope or Ody v2?

I always screw up or end up 3-5 ohms - using 30awg...

Any affordable wire welder recommend?

Thanks in advance


Sent from my iPad using Tapatalk HD

I would like to see this as well for P V2

 

[Dontknow]

30awg (if it's Kanthal A1), should be about 30 ohms per meter. Or 0.3 ohms per cm, or about 0.75 ohms per inch. You should be able to make micro coil or small wound coil with 2 inches or less of 30awg wire, this would be around 1.5 ohms for 2 inches of wire - or 1.1 ohms for an inch and a half of wire...


Sent from my iPad using Tapatalk

 

[FogNL]

Dear PV2 users,

I wonder What is the common wisdom is on wick setups doubled on top. The short wick on top or below the longer wick that goes down in the channels?

 

[Dontknow]

Dear PV2 users,

I wonder What is the common wisdom is on wick setups doubled on top. The short wick on top or below the longer wick that goes down in the channels?



To quote the great Puerto Rican poet Ricky Martin - "She Bangs"!..


Sent from my iPad using Tapatalk

 

[dutch onsea]

Sam&Black I'm using 28 gauge kanthal 10 wraps round a thumbthack. Welded it together with a zapper. This gives me 1.4 ohm. A bit hard to get the cotton through, just don't use too much, nothing in the channels. SUPERvape

 

[dutch onsea]

https://docs.google.com/spreadsheet...ZEtmY0pPYzBvdUw2blJHVjdkc1E&usp=sharing#gid=0
This was given to me, very handy...

 

[Bigwhiterabbitt]

Can anyone tell me how is the temperature of the vape in short mode compared to normal mode? Is it a lot hotter?

 

[s1mp3]

Not much of a difference, in my opinion.

Sent from my thumb

 

[subver]

Hey so what Ody parts would I need to turn Penny v3 into a dripper?
Imeo did you say if you were making a spider cap for Penny v3 or not? If so I will wait and get that (depending on when it would be available) but if not I will use the Ody drip parts.

 

[imeothanasis]

ody drip mouthpiece is just fine sub. Also its very classy too

 

[subver]

I don't see it listed on e-smokeguru (or CoV), Imeo, am I just blind?

 

[subver]

One more question, will the Penny v1 O-rings fit the v3, or should I buy Penny v2 O-rings to fit the v3?

 

[imeothanasis]

check o-rings guide sub

 

[D Stanley Querfurth]

-wrong post-

 

[imeothanasis]

I just saw that the item is out of stock sub. Tthey were up for sale for enough time but you missed it maybe

I don't see it listed on e-smokeguru (or CoV), Imeo, am I just blind?

 

[subver]

I just saw that the item is out of stock sub. Tthey were up for sale for enough time but you missed it maybe

Aw bummer - I will check around, thanks Imeo! You Rock! Ever since the first day I got my Odysseus, I scrapped every other ecig item I've had and became obsessed with GG stuff.. it's all I use!

Now.. anyone got a spare Ody dripper mouthpiece to sell?

 

[Dontknow]

Penelope V3 centre post sold out already at ESG! The site was a little late getting up. Then got everything into the basket - except the centre post! Now what? When will there be more spares available to complete the order to convert V2 to V3?
Also - in case I made a mistake - other than the wire holding small screws, how many other parts need to be doubled up on?
Mostly though - more spares? So I can complete my order.....

 

[subver]

Penelope V3 centre post sold out already at ESG! The site was a little late getting up. Then got everything into the basket - except the centre post! Now what? When will there be more spares available to complete the order to convert V2 to V3?
Also - in case I made a mistake - other than the wire holding small screws, how many other parts need to be doubled up on?
Mostly though - more spares? So I can complete my order.....

It's always good to have spare o-rings