Oh yes it is being cloned. Haven't seen one in the wild but have seen the clone on the net.
Sent from my One using Tapatalk
Sent from my One using Tapatalk
RDA Plume Veil Clone
- Thread starter Cullin Kin
- Start date
- th_trl_thread_readers 0
- Status
I received a plume veil clone from fasttech.... First device I have ever ordered from them, and was pleasantly surprised. It was so cheap I just had to buy it and see what I would get...
It actually looks pretty darn good. The build deck looks better machined than some of the authentic as far as the post holes go.... The only thing that is questionable is the screws on the negative posts... They are super super hard to turn, and they will probably strip very soon haha. I'm going to try and build as little as possible to avoid stripping them...
I cleaned it very very well, then built a dual 24 gauge 7 wraps, I believe it came in at about .4 ohms. The flavor is fantastic, and great vapor production. My only complaint is that it leaks..
Over all for the $15 bucks I spent, it is a freaking awesome atty.
It actually looks pretty darn good. The build deck looks better machined than some of the authentic as far as the post holes go.... The only thing that is questionable is the screws on the negative posts... They are super super hard to turn, and they will probably strip very soon haha. I'm going to try and build as little as possible to avoid stripping them...
I cleaned it very very well, then built a dual 24 gauge 7 wraps, I believe it came in at about .4 ohms. The flavor is fantastic, and great vapor production. My only complaint is that it leaks..
Over all for the $15 bucks I spent, it is a freaking awesome atty.
Ya. I've heard too. what is the differenct in the 1.5? Just a full plated deck?
That and more air holes on the top of the device. The negative post air holes might be different as well but I am not sure.
Oh and a silver plated 510 pin.
Sent from my One using Tapatalk
Last edited:
Deeper juice wells, more adjustable airflow, silver plated brass contact, gold plated base and screws, a shortened 510 connection, and the main coil airflow has been widened.
The Vape Source - Plume Veil V1.5 RDA by Aethertech
They listened to Rip, and made the logo and writing much smaller. Looks really good, and if it is an improvement to the already fantastic atty, it is going to be a beast.
I've tried 3 different versions of the plume veil clone and I have to say, I think the tobeco is the best one
surprised as tobeco is usually a bust.
surprised as tobeco is usually a bust.
Got my acerig clone off. eBay. The screw sizes are right, but the threading in the posts are crap. Had to torque the crap outta the screw to get it into the post. It's a lot better after a few screw and unscrewing.
In any case, does anyone know what are the diameter, pitch and length of the plumeveil screws?
Burping out loud using Tapatalk
In any case, does anyone know what are the diameter, pitch and length of the plumeveil screws?
Burping out loud using Tapatalk
Get it on your ipv where airholes won't hit your finger or hand..sucker hurts.. properly is responsible for touch sensor going haywire..
I love mine..I replaced the afc oring with an oring for the base. I saw a 454..the well does not exist...I was surprised..about the size of plume veil.
I saw the sigelei Taj whatevers.. but the 22mm one may get in my rotation.. beautiful domed cap(inside..I forgot and don't care what it looks like outside)..top cap was hard to get off..but looks like a better origen.
smiles.
Tobeco ehpro and acerig. I believe. Maybe a fastech version too.
Sent from my One using Tapatalk
Sent from my One using Tapatalk
"."Overall, I'm not completely satisfied, and all my excitement keeping track of this thing on USPS tracking wasn't worth it yet".
LMAO!!!
LMAO!!!
yup the FT Plumeveils dont have dodgy center posts that spin on there own, just saying
The 510 pin on mine sticks out really far........... Even when tightened all the way, it stick out so far I am barely able to thread it on my nemesis. I have not torn it apart, since its a clone I dont want to break anything I cant figure out how to fix.....
The post holes on the neg and pos block are pretty much even, seems like if I could raise the pos block higher, the 510 pin would go up too... I think mine is made by AMOD... though not sure, since I got it at a local B&M, and the store swapped it into a wooden box for me so I'd get the drip tip (very nice of them), but the paper cardboard box it was originally pulled out of said AMOD, however since they swapped it into a wooden box with a lightening bolt on it for me, I cant be sure the amod box was the original box in the first place.
The post holes on the neg and pos block are pretty much even, seems like if I could raise the pos block higher, the 510 pin would go up too... I think mine is made by AMOD... though not sure, since I got it at a local B&M, and the store swapped it into a wooden box for me so I'd get the drip tip (very nice of them), but the paper cardboard box it was originally pulled out of said AMOD, however since they swapped it into a wooden box with a lightening bolt on it for me, I cant be sure the amod box was the original box in the first place.
EH pro has better build quality than the original, been vaping this thing non stop since friday. Haven't picked up my mutation.. Seriously the EHpro version is IMMACULATE.
I originally gave up on the plumeveil but I recieved the infinite version in the mail the other day and I have to tell you this thing is a perfect as the og I promise you buy this thing
Plume Veil is my first RDA, I normally vape on menthol type of liquid (diy). For 30ml with 12mg nic, I normally use 8-10 drops to get that menthol sensation on cartos or 357 atomizers but the menthol and nic sensation is overwhelming.
Is this normal? My build is 1.8-2.0 ohm single coil on authentic Nemesis.
Is this normal? My build is 1.8-2.0 ohm single coil on authentic Nemesis.
- Status
Similar threads
