SvoёMesto KAYFUN 4

[Moonbogg]

Holy balls. Its awesome. I'll fix the gap later. For now its vaping sick awesome. I took the airflow screw out and now I have a nice lung/mouth hit hybrid going on. More vapor than the KFL. I start with a little lung hit, just a gentle one and finish it out with a mouth pull. Looks sick. Just gotta watch for dry hits and such but I feel good about it.

 

[thmstwwng]

Moon, I don't know what causes it as I have not had the issue. At least one other member has, but it was corrected with a reassembly. Sorry I can't explain it, but know it has happened and can be fixed.

Mine won't flush all the way. I tried just the P3 connector (without K4) & P3, it won't flush all the way.

I've email SvoeMestro, they ask me to check with ProVape.

 

[raitizz]

Mine won't flush all the way. I tried just the P3 connector (without K4) & P3, it won't flush all the way.

I've email SvoeMestro, they ask me to check with ProVape.

Does yours look like this? 2,5 threads?

R

 

[AstroTurf]

So SMtec GmbH sent me a clone directly from Everswinkel?? If so, that's a nice one

R

Dang... You gotta clown directly from the manufacturer?!?

Wicked Sick Man, Wicked Sick.

A collectors Item for sure!

LOLz, Jim

 

[raitizz]

Dang... You gotta clown directly from the manufacturer?!?

Wicked Sick Man, Wicked Sick.

A collectors Item for sure!

LOLz, Jim

I know, right !?!?!?!

No words can describe it, no words...

R

 

[AstroTurf]

I know, right !?!?!?!

No words can describe it, no words...

R

I am now sooooooooooooo Jealous!

 

[raitizz]

I am now sooooooooooooo Jealous!

You still waiting on the V5?
If you had the V4, I'd say check if the logo is centered between two airholes or not. If NOT, and I assume you'd get an authentic, then it would be an authentic clown!!!! A museum piece, too!


R

 

[AstroTurf]

You still waiting on the V5?
If you had the V4, I'd say check if the logo is centered between two airholes or not. If NOT, and I assume you'd get an authentic, then it would be an authentic clown!!!! A museume piece, too!


R

Yes, Thats how I roll...

V5 comes out, Then buy a V4!

LOLz, Jim

 

[thmstwwng]

Does yours look like this? 2,5 threads?

R

Looks like it. Why?

 

[raitizz]

Looks like it. Why?

View attachment 405667

OK, the P3 connector is the real deal and the insulator sits flush in the base?
It takes the connector 1/4 of a turn from touching the pin until full stop (at least on mine).



R

 

[thmstwwng]

OK, the P3 connector is the real deal and the insulator sits flush in the base?
It takes the connector 1/4 of a turn from touching the pin until full stop (at least on mine).

View attachment 405674

R

I guess so but it got nothing to do with the insulator or the pin cause I tried with the p3 connector only (without the k4 install) it still got small gap. BTW are you using the P3 commercial release (without diamond design) or the beta unit?

 

[Moonbogg]

Mine won't flush all the way. I tried just the P3 connector (without K4) & P3, it won't flush all the way.

I've email SvoeMestro, they ask me to check with ProVape.

You tried it without the contact pin installed? It was just the P3 base by itself and it still wouldn't sit flush? If that's the case then the P3 connector needs to be trimmed on a lathe.

 

[raitizz]

I guess so but it got nothing to do with the insulator or the pin cause I tried with the p3 connector only (without the k4 install) it still got small gap. BTW are you using the P3 commercial release (without diamond design) or the beta unit?
View attachment 405677

Oh, sorry, yes, you said that you tried without the pin. Where did you get that connector?
Yes, I use the retail version. Mounted out of the box, no gaps.
Have you contacted ProVape yet?

R

 

[rcbell.N51]

I guess so but it got nothing to do with the insulator or the pin cause I tried with the p3 connector only (without the k4 install) it still got small gap. BTW are you using the P3 commercial release (without diamond design) or the beta unit?
View attachment 405677

Me too. Screwing on just the connector, with nothing else assembled (no positive pin, nothing), to the P3 and P2.5 Mini Ti and I still have a gap. The gap is big enough to slide a piece of paper between the the two parts but not two sheets.

The fact that it fits neither the P3 or the P2.5 Mini Ti leads me to believe the issue is SvoeMesto's rather then ProVape's.

 

[thmstwwng]

Me too. Screwing on just the connector, with nothing else assembled (no positive pin, nothing), to the P3 and P2.5 Mini Ti and I still have a gap. The gap is big enough to slide a piece of paper between the the two parts but not two sheets.

The fact that it fits neither the P3 or the P2.5 Mini Ti leads me to believe the issue is SvoeMesto's rather then ProVape's.

Agreed. P3 was launch first and the connector comes second.

 

[Moonbogg]

My epic gap. Its pretty large. I will try installing without the pin to see what happens. Looks like I'll be modifying the pin, the connector, or get used to it and live with it.

 

[dems86]

My epic gap. Its pretty large. I will try installing without the pin to see what happens. Looks like I'll be modifying the pin, the connector, or get used to it and live with it.

Damn, channeling Michael Strahan up in this piece

 

[Moonbogg]

Damn, channeling Michael Strahan up in this piece

lol, so true.

 

[Bronze]

Maybe I missed something. Is there a benefit to informing the members of this thread what their serial numbers are? Are we trying to determine a range of valid numbers or something?

 

[Mtek]

You tried it without the contact pin installed? It was just the P3 base by itself and it still wouldn't sit flush? If that's the case then the P3 connector needs to be trimmed on a lathe.

Moon, I have a diamond P3 (beta). The base on mine did leave a paper-thin gap at first but I twisted the base on pretty good and it closed. Probably used more force than some are comfortable with. I knew the pin has an oring underneath in the design, allows for some movement. I have had no issues since, and zero gap since. I can spin it on easy now and it closes, perhaps I was just lucky.