Yea only secure using the screw heads and make sure they are very tight.
You're welcome, enjoy!
SXmini M Class (TEMP CONTROL)
- Thread starter whitewidows
- Start date
- th_trl_thread_readers 0
- Status
Yea only secure using the screw heads and make sure they are very tight.
You're welcome, enjoy!
Which mode are you in when you "hold[ing] both buttons in"? Power or Joule?
Should be Power. Check the Manual...CORRECTION Joule mode is fine...per the Manual.
Sent from my iPhone using Tapatalk
Last edited:
Thanks. Thats what I figured too. Guess will just wait for the INR18650-30R another couple of months.
Found this one too...... but just no way it can be real. I'm sure its just a re-wrap with false info.
I wouldn't use that battery either. That said I'll use other 18650s besides VTC4s. While your point about being subohm is true, its not like we are putting 4.0v to our ni200 coils.
Take .07 as example, close to the "recommended" resistance, even at 50W, its only pulling almost 28 amps. Which any of the good 2500mah 35A pulse batteries can easily do.
I was doing it in Joule mode for the first one for sure. Read the manual, but don't recall it actually specifying on that to be honest (don't have it here)
Thanks. Thats what I figured too. Guess will just wait for the INR18650-30R another couple of months.
Found this one too...... but just no way it can be real. I'm sure its just a re-wrap with false info.
I stick with 25Rs HE4s and vtc4s only for everything. I know those, I trust them and they've been pretty well tested in vaping. The battery is the most important part not to cut corners on.
With a 200$ mod, and pushing high wattage, I figure saving 5$ on a battery or using a battery marketed to the one community is probably a bad idea.
In my head, when I see something marketed especially for vaping by an unknown source my first thought is someone dumpster diving for cells to rewrap and cash in.
*EDIT* Ignore, I read the spec sheet and apparently the chip will pull 30a in TC mode and 40a in Kanthal mode, wow...
Last edited:
You are correct and I was wrong.
From the start I've been taking the added precaution of going to Power mode as though I'd installed a fresh battery (which usually has gone together for me).
Sorry for the mistake.
From the start I've been taking the added precaution of going to Power mode as though I'd installed a fresh battery (which usually has gone together for me).
Sorry for the mistake.
Jazz,
Oops we must have posted simultaneously. Bet we couldn't do that twice in a row.
Regards,
George
Last edited:
I'm seeing 30 amps input with >25 amp battery requirement across the board for the SX350J specs. Is there info that is different elsewhere?
I agree with you tchavei. I think it was a full contact coil and TC just doesn't work with that very well. It was also such a massive coil with 26 ga which is just too thick.
Something is wrong, on Steam Engine:
30AWG NI200
single coil
Target resistance 0.262Ω
Inner diameter of coil 3MM
comes out to 12.15 wraps
Running 6wraps would give you 0.14Ω
I hear you but I just prefer to use VTC4 over anything else on the market. Better safe then sorry. It also allows me to use more than just an ni200 build on the go if I wanted to. Sometimes I carry around my Mutation X V3 with a .20ohm or less parallel kanthal coil in it.
I just put on my 2nd Kanger OCC NI200 coil. The first one I used for about 8 days of heavy vaping. The new coil is showing .133 ohms, the first one was about .125. I notice a vast improvement with taste with the new coil. .22 is just way too high for that coil and I am running at 28J with 415 degrees using a max VG juice.
I have been looking at the Lemo 2 and/or the Smok VCT-Pro if I can get NI200 coils for it. Does anyone know if they are available for it yet?
Technonaut had a post a few pages back about a smok ni200 coil but I wanna say that was for the gimlet?
I think
I did order a lemo2 also, should be here tomorrow or Friday.
I sent an email to Smok about Smok VCT-Pro NI200 coils, they replied that they will announce the release soon.
quality@smoktech.com <quality@smoktech.com>
Apr 14 (1 day ago)
to me
Dear Sir,
Yes, we will announce it very soon. Thanks!
SMOK Customer Service Team
Website: www.smoktech.com
Follow us At SMOK facebook fanpage https://www.facebook.com/SMOK.TECHNOLOGY
Youtube Channel: http://youtu.be/dGrRpddHiR4
From: Yahoo
Date: 2015-04-15 10:33
To: quality
Subject: Smok VTC Pro question
Last edited:
Lemo 2 is awesome! Just make sure you close the airflow on the base when you fill the tank from the top. Also don't fill it all the way up, leave a little room (like 10%) to prevent leaking as soon as you reopen the airflow. It wont leak any other time.
awesome!!! wanted a good single coil rta to run in temp mode. and im really not a huge fan of m kf4, almost everything I have are dual coil attys though.
I just got a silerplay today, grabbed it out of the classis and im totally impressed vapor wiae, but I had to add flavor to my juice because it was so muted
Last edited:
I agree with you but I have found it is a smart idea after opening the air flow to hold a tissue against one of the air slots and tip it horizontal and let the tissue catch any juice that has gotten into the air chamber. Once you do that it is good to go and no further leakage.
- Status
