SXmini M Class (TEMP CONTROL)

[Quantum Mech]

You running single Coil or dual Coil Ti and what GA at that Temp?

5 wraps of 26awg at 3mm ID ... which comes in between 0.265-0.280ohms

Only running at 17j and that is plentiful to have her whingeing about clouds

Double result as she goes to bed to watch TV, so whingeing stops and I am allowed to touch the remote control

 

[Quantum Mech]

I am going to ask this question here first because I know a lot of you have a Subtank Mini & use temp. control. I have one as well & I have some extra acrylic bell cap/tanks I got separately for the STM. Has anyone used or had problems using an acrylic tank & temp. control?

Will be a bit of trial an error I think with TP

Used one with a 0.3ohm kanthal build I was running at 40w

Did not like the bottom of the chimney getting a bit deformed/melted

Maybe its not an issue or maybe that means I was vaping acrylic

 

[Hitcat44]

5 wraps of 26awg at 3mm ID ... which comes in between 0.265-0.280ohms

Only running at 17j and that is plentiful to have her whingeing about clouds

Double result as she goes to bed to watch TV, so whingeing stops and I am allowed to touch the remote control

Roger That. Thanks.
Running a 5/4 26 Ga at about 2.6mm I.D. and yielding 0.23-0.24 so should be copasetic at that Temp. Will try 17.5J and see where that takes me.
Have the Joule Presets starting there and upwards at 2.5J Increments which should about cover it in most Instances.

 

[2legsshrt]

Roger That. Thanks.
Running a 5/4 26 Ga at about 2.6mm I.D. and yielding 0.23-0.24 so should be copasetic at that Temp. Will try 17.5J and see where that takes me.
Have the Joule Presets starting there and upwards at 2.5J Increments which should about cover it in most Instances.

I got lost there are you guys running in Ti mode or Ni mode. What is the temp you are running at. Which batteries were decided to be the best between VTC4 25R or what I am thinking of getting a few more and all are around the same price at RTD. The VTC4 is on sale for 7.99 the 5 is 10.99

 

[2legsshrt]

The reason I am asking in a couple days will have my Ti wire and that is the build I was going to use the one QM is using. What temp and what mode is it working so well on.

 

[Hitcat44]

Running in Ti Profile. I'm using 25Rs in the SX. Was running at 400-440* but will try 480-490 when get Home as QM & Jim are doing.
Occasionally will go to Ni200 Profile (with Ti Coil) and lower the Temp to 300* F to account for the Firmware difference in Algorithms.
I do that to compare Vapor Qty & Flavors to see if the functioning on the Ti Profile is optimized and comparable. Still not digging the Test Firware. Believe it is anomalously "glitchy & twitchy" (not same for every User or Device).
I know that sounds illogical and call me crazy but I'm damn near convinced.

 

[2legsshrt]

Ok maybe I will load it on one or two of mine and give it a try. I'll be using the STM since that is all I have anymore. 440-460 17J 26awg 3mm 5wraps. Got it. Hope they get the final version out soon. Might load it on all of them and I can always switch to the nickel mode if I don't care for it.

 

[2legsshrt]

I wonder if QM is using the Vape Mesh brand he is the one that told me about it but mine shipped today so I will have the Unkamen for that period of time.

 

[Jake67]

I am going to ask this question here first because I know a lot of you have a Subtank Mini & use temp. control. I have one as well & I have some extra acrylic bell cap/tanks I got separately for the STM. Has anyone used or had problems using an acrylic tank & temp. control?

Using the bell cap on 2 STMs. No issues with temp control.


Sent from my iPhone

 

[Ardy]

whingeing

Had to look that one up

 

[Hitcat44]

Had to look that one up

You too eh.... The Colonial Urban Yankee Dictionary defines it as; "King's English" for the Act of engaging in Incessantly Acerbic Whine-Baggery.
Well played QM ol' Chap.
Learn something everyday here in this Thread. Really quite multi-Educational

 

[ThunderDan]

I still don't know what that means.

 

[Unior]

Did you ever get a shipping # ?[/QUOTE
I SXM TODAY! But to answer your question I got an email with the order # the day after I ordered (7/2/)The SXM was on back order for a week they said. On 7/7 they sent email that it had shipped w/ free 2-day shipping. Got it 2 days later. So far so good with breazy.com. Of course a button may fall off tonight & I may not be able to get anything done

 

[Unior]

Sorry I screwed up that post. But yes I got order # etc. all good as you can see

 

[Unior]

Factory date is 6/8/15. That being said is the paint going to come off this thing anyway?

 

[JimScotty0]

Silicone Sleeve for the SXmini M Class

It looks like VariTube is now selling the new Silicone Sleeve for the SXM and only $7.95. Not a bad price!

Beautiful Silicone Sleeve made for the SXmini M Class by YiHiecigar. Not a knock off.
Protect your investment with this perfectly fitting sleeve. Black only available.
Silicone Sleeve for the SXmini M Class

I want one!

 

[Marc411]

Can't go wrong buying anything from Varitube, Perry runs a great shop and takes care of his customers!

 

[mr.fabe]

Factory date is 6/8/15. That being said is the paint going to come off this thing anyway?

My factory date is 3 days earlier 6/5/15.. My paint is ok. I think you'll be fine.

 

[Vlad1]

5 wraps of 26awg at 3mm ID ... which comes in between 0.265-0.280ohms

Only running at 17j and that is plentiful to have her whingeing about clouds

Double result as she goes to bed to watch TV, so whingeing stops and I am allowed to touch the remote control

Not sure what I've got going wrong here but received my 26g Ti today from Unkamen, Built several coils at 5 wraps around 7/64 mandrel and all locking in at .235Ω - .236Ω several different builds but cant seem to get a stable temp compared to ni200. I have to go up to 560 or above to get the same warmth vapor I was getting with ni200 at 415 - 430 or so. Also doesn't seem to be as stable in Ti01 mode in regard to the temp bouncing as ni200 mode has been pretty stable at the temp limit. Any idea what I may have overlooked?

 

[Yozhik]

Not sure what I've got going wrong here but received my 26g Ti today from Unkamen, Built several coils at 5 wraps around 7/64 mandrel and all locking in at .235Ω - .236Ω several different builds but cant seem to get a stable temp compared to ni200. I have to go up to 560 or above to get the same warmth vapor I was getting with ni200 at 415 - 430 or so. Also doesn't seem to be as stable in Ti01 mode in regard to the temp bouncing as ni200 mode has been pretty stable at the temp limit. Any idea what I may have overlooked?

Sounds like a connection problem. I'd use a different atomizer and see what happens.