Tank-O-Matic Liquinator v4.1

[TrancePsychosis]

The only juice I've tried in there is Elvis Presley from diyflavorshack. I haven't detected any taste from the vinyl leeching into the juice. My local stores don't carry the Polycarbonate tubes, which was my first choice. But after much Google'ing I could not find anything suggesting that there would be an issue with the vinyl. They do use it in soda machines and distilleries so I assume it would be safe.

 

[jonny2hottie]

any texan local drop by to see if they could show a preview of the BFT? im interested in what it might look like an how much $ it would cost.

hey this is my 666 post!

 

[BigCypress]

thanks for the replies, looks like i'll be waiting to cut my cartos till i get mine tomorrow... The wait is killing me!!! i've refilled my carto at least 20 times today

 

[light487]

Currently 12:40pm here; refilled the 3.5ml Liquinator last night around 8:30pm and have refilled it again this morning at around 11pm... I love that side benefit too

 

[Myrkos]

Currently 12:40pm here; refilled the 3.5ml Liquinator last night around 8:30pm and have refilled it again this morning at around 11pm... I love that side benefit too

Yea I can't wait until my other tanks get here so I can just fill them all and swap flavors with my mood.

 

[junjunb]

BigCypress, I punched my holes 14mm ( or just a little over 1/2 in) up from the threads, based off of what I found on this youtube video that I'm having some difficulty locating.

I think this is the video (2:20)
http://www.youtube.com/watch?v=o-49YN6RzXg


Got a quick question from a noob.
Been reading a lot of positive feedback re the Liquinator,
only "complaint" I noticed is the "slidey" issue.
I saw an update from the Vaporescence site, saying that they already addressed this by redesigning the interior seal.
Any feedback if the "slidey" issue is now fixed with this new version?
(I guess this question goes out to guys who just purchased the Liquinator)

Thank you very much for your inputs!

 

[Xaria]

It's hard for me to compare as this is my first one, but I have read posts in this thread. The one I received yesterday does not slide at all.

 

[BigCypress]

jun, I'll let you know in a couple hours as mine is coming today. Thanks for finding that vid too!

 

[Chief-A-Lot]

I think this is the video (2:20)
Liquinator Walkthrough.MTS - YouTube


Got a quick question from a noob.
Been reading a lot of positive feedback re the Liquinator,
only "complaint" I noticed is the "slidey" issue.
I saw an update from the Vaporescence site, saying that they already addressed this by redesigning the interior seal.
Any feedback if the "slidey" issue is now fixed with this new version?
(I guess this question goes out to guys who just purchased the Liquinator)

Thank you very much for your inputs!

None of my Delrin tanks slide one bit... I assume that the issue they addressed was using the proper o-rings... Which I Beleive they have. My SS is tight enough where pocketing isn't a problem at all. It's still not quite as snug as my Delrin ones. On that note, I am completely satisfyed with all my tanks.

 

[Big Fran]

I'd like to suggest a fix for this.......It's very cheap. I'm not 100% sure bit I think it's worth a shot. Try to replace the inside o-rings with these. I think it may solve all your problems.
McMaster-Carr

I ordered thies o-rings and now I cant get the carto back in. It seems to tight. Is there a trick to this?

 

[Hellen A. Handbasket]

Fran, did you put some PG or VG on the o-rings/caps? That should help.

 

[junjunb]

@Xaria and Chief - Thanks for the feedback, appreciate it!
@BigCypress - Looking forward to it!, Thanks as well!

 

[Big Fran]

Fran, did you put some PG or VG on the o-rings/caps? That should help.

Yes I did use some vg. I think the o-rings are just to large. I put them in SS caps so the caps wont give any to help get the carto in.

 

[fsroq]

First time I putted a cart in it I also thought it wouldn´t enter. You have to push real hard, it wont break, that is what I was afraid for.

 

[Big Fran]

Well I got it in but it cut a "C" of rubber out of the o-ring. It is tight. I'll have to see if it leaks.

 

[Chief-A-Lot]

Well I got it in but it cut a "C" of rubber out of the o-ring. It is tight. I'll have to see if it leaks.

That's what happened to my replacment SS Tank... And it was due to the Slotted cartomizer... Punch method will be the only method I use from now on.

 

[Big Fran]

That's what happened to my replacment SS Tank... And it was due to the Slotted cartomizer... Punch method will be the only method I use from now on.

The top of the carto did it. I put a punched XL duel coil on it from Vapor Age. The pice of rubber came out the top when the cap was pushed on.

 

[Chief-A-Lot]

The top of the carto did it. I put a punched XL duel coil on it from Vapor Age. The pice of rubber came out the top when the cap was pushed on.

Dayum your stronger then I thought! Hehe, but seriously, are you noticing any issues from it?

 

[SKYYcamel]

A few quick questions. Sorry, I don't have to time to research this whole thread. Is punching holes in the Boge 510 cartos working better than Dremeling the slots? If so, how are you punching the holes? Thanks!

 

[Big Fran]

Dayum your stronger then I thought! Hehe, but seriously, are you noticing any issues from it?

They don't call me Big Fran for nothing.(6'5" 280lbs.) LOL

It is working fine. It's not leaking and it is very tight. I guess it just cut it to the right size.