~The Billet Box~ page 1559 continued...
- Thread starter Doug Dino
- Start date
- th_trl_thread_readers 0
- Status
Speaking of lazy, I've noticed something with using the MTL base.
One of the things that can suck when using a BB is you need to change a coil or rebuild and you've got a full tank of liquid... It's my only con to the device, because you're likely going to have to drain the liquid and sometimes you lose some in the process etc.
But with the MTL base in use, invert the tank and if your liquid is below the top sleeve of bridge then you can just pull the base/coil out and change with ease!
That's how I tested both bases to see which airflow I liked better.
Sent from my Pixel 2 XL using Tapatalk
--> Drizzle - me - Nizzl <--
Got the Bridge. Used the 2 x 1 mm Hole and the drizzle 1.3 ohm coils.
Needs to soak a bit more liquid in to the ceramic but from the airflow it is exactly what i was looking for.
Now need to think and create a disc for the normal coils so i can use both types.
THANK YOU ALL for your help and experience. Expect to grow my belly now as i do not leave the couch for coiling anymore... mUhAAA....
Got the Bridge. Used the 2 x 1 mm Hole and the drizzle 1.3 ohm coils.
Needs to soak a bit more liquid in to the ceramic but from the airflow it is exactly what i was looking for.
Now need to think and create a disc for the normal coils so i can use both types.
THANK YOU ALL for your help and experience. Expect to grow my belly now as i do not leave the couch for coiling anymore... mUhAAA....
Well I watched his videos all the time, Mark is the reason I decided and got the BB and the vapeshell. I did my build for the cotton just like his and still get condensation. Thank you
@GeekyGeezer & @Susaz
Will try to get a few of those printed. Just a Ring between the bottom piece which reduces the airflow down to 2 x 1 mm. And maybe 2 x 1.5 mm. Should be sufficient for a "good" MTL draw on the "big" EUC coils.
Will report as soon i get them and share the file.
Will try to get a few of those printed. Just a Ring between the bottom piece which reduces the airflow down to 2 x 1 mm. And maybe 2 x 1.5 mm. Should be sufficient for a "good" MTL draw on the "big" EUC coils.
Will report as soon i get them and share the file.
Now THOSE look like they would do a good job. I'm wondering if there might have been a mistake in some of the MTL adapters. Seriously, mine have what I'd describe as pinholes, much smaller than any air hole on any MTL atty I've ever used.
I know it's not a solution for many, but I got the "big" coils dialed in to my draw preference by a generous amount of cotton under the boro.
Morning all.
So, ordered 3 types of rings now. 1x1.5 / 2x1 and 2x1.5 mm AFC. Ask the printer guru to print them in rubber.
Would be great if this would help so i could run the normal EUC coils as i do expect more volume out of them.
Plus you can buy them more often.
Should get them to the weekend and will report.
PS: If they work i can send you a kit. Ordered 4 Kits.
So, ordered 3 types of rings now. 1x1.5 / 2x1 and 2x1.5 mm AFC. Ask the printer guru to print them in rubber.
Would be great if this would help so i could run the normal EUC coils as i do expect more volume out of them.
Plus you can buy them more often.
Should get them to the weekend and will report.
PS: If they work i can send you a kit. Ordered 4 Kits.
So, here some words on the ModFactory MF BB Bridge for Vaporesso EUC Coils
- MTL Kit is only for the Drizzle Coils (1.3 + 1.4 OHM)
- Normal Kit is for standard EUC Coils (0.3 - 0.6 Ohm)
I did draw and let print an Airflow Reducer Ring for the Normal Bridge as i wanted the normal EUC coils but for MTL. Easier to get. Cheaper sometimes and more Volume. The rings were printed with rubber like filament so they can be squeezed into the right height and position. 2 x 1 & 2 x 1.5 & 1 x 1.5 mm Airholes to test now.
The draw is really reduced to a minimum compared to the openness they had before. Bit more airy as the MTL kit with the drizzle coils but this is from the build of the coils. Chimney is wider as well.
Here is the link to the STL Files of the ring. Just give these to your printer guy.
Modfactory_MTL_Rings.zip
- MTL Kit is only for the Drizzle Coils (1.3 + 1.4 OHM)
- Normal Kit is for standard EUC Coils (0.3 - 0.6 Ohm)
I did draw and let print an Airflow Reducer Ring for the Normal Bridge as i wanted the normal EUC coils but for MTL. Easier to get. Cheaper sometimes and more Volume. The rings were printed with rubber like filament so they can be squeezed into the right height and position. 2 x 1 & 2 x 1.5 & 1 x 1.5 mm Airholes to test now.
The draw is really reduced to a minimum compared to the openness they had before. Bit more airy as the MTL kit with the drizzle coils but this is from the build of the coils. Chimney is wider as well.
Here is the link to the STL Files of the ring. Just give these to your printer guy.
Modfactory_MTL_Rings.zip
Attachments
The holes on MTL bases are advertised as 1mm but they're definitely not. Nearly everyone I've seen with a MF bridge using MTL has drilled out the holes for actual 1mm holes.
I drilled both of mine with a #62 bit and they're perfect now.
Sent from my Pixel 2 XL using Tapatalk
Morning!
Anyone heard something new from the Haku Bridge?
Last thing i read was testing mode...
Thanks
Anyone heard something new from the Haku Bridge?
Last thing i read was testing mode...
Thanks
So some words to the MF Bridge after testing it.
The rubber rings do help very good to restrict the draw on the normal EUC bridge.
About the MTL add on. @autobiogphnation , yes had to drill out mine as well.
Will get another bridge and some of these delrin plugs for the drizzle extra. So i can drill them out to 1.5 mm.
All in all i have to say that i am very satisfied with the bridge and can use it as MTL very good.
Also the drop in coils especially the ceramic ones do deliver a good flavour.
Ok, the heat on the normal EUCs is about 35 Watt to get a decent warm vape. And for the smaller drizzle i do vape them at 14 Watt. Will test the claptons next with a little bit of Punch Mode on the DNA60.
Ah.. i was not able to vape the drizzle ceramic heads in TC. Anyone else or was that just my coil?
The rubber rings do help very good to restrict the draw on the normal EUC bridge.
About the MTL add on. @autobiogphnation , yes had to drill out mine as well.
Will get another bridge and some of these delrin plugs for the drizzle extra. So i can drill them out to 1.5 mm.
All in all i have to say that i am very satisfied with the bridge and can use it as MTL very good.
Also the drop in coils especially the ceramic ones do deliver a good flavour.
Ok, the heat on the normal EUCs is about 35 Watt to get a decent warm vape. And for the smaller drizzle i do vape them at 14 Watt. Will test the claptons next with a little bit of Punch Mode on the DNA60.
Ah.. i was not able to vape the drizzle ceramic heads in TC. Anyone else or was that just my coil?
Eh, TC on a BB ain't worth it. DNA60 just really ain't built for that. Everything is default values from evolv on the thermals and you have no way to run case analyzer on a DNA60.
Yes, you can turn on TC and change it to SS etc but it's not going to be accurate and will likely cutoff super fast.
Sent from my Pixel 2 XL using Tapatalk
"Yes, you can turn on TC and change it to SS etc but it's not going to be accurate and will likely cutoff super fast."
Well, with the normal EUCs i was able to use TC. Anyway i am not the TC guy at all. Very happy that my setups are running. Now i need to vape a 100 years to compensate my spendings .. haha
Well, with the normal EUCs i was able to use TC. Anyway i am not the TC guy at all. Very happy that my setups are running. Now i need to vape a 100 years to compensate my spendings .. haha
Happy Valentine’s Day, fellow BB’ers!
It’s getting frisky over here...but you know I can’t stop them!!!
It’s getting frisky over here...but you know I can’t stop them!!!
So quiet in here...
I see how it is...
SvöeMesö announces a new Kayfun [lite] and everyone forgets about the Billet Box for a minute!
[emoji23][emoji23][emoji23]
I see how it is...
SvöeMesö announces a new Kayfun [lite] and everyone forgets about the Billet Box for a minute!
[emoji23][emoji23][emoji23]
Odis Boxxer v2 pics came out today... So I'll leave those here and maybe things won't be so quiet here...
Sent from my Pixel 2 XL using Tapatalk
- Status
Similar threads
- Locked
- Locked
