The Darwin From Evolv!!!

Status
Not open for further replies.

the ob

Unregistered Supplier
ECF Veteran
Jan 31, 2011
7,577
12,011
Portlandia
I am curious. I ordered another. I was told that the new ones would be more expensive (but we were able to use the save5 discount) One of the reasons that they were more expensive is because they would all come with a 510-510 adapter permanently attached. Mine came without this done. I emailed with no response. I called and was told that some were sent without this done because they ran out. When I questioned them about this and the price increase, I was told they would try to look for some and see if they were lying around.

I guess I am just surprised. I have read over and over about Nhalers amazing customer service. They have been really diligent about emailing me and reminding me when they were going on sale when I asked them to. Now that I have a issue (even though it is a small one) I cannot get a answer or get it resolved.

Did those of you that received them in the last couple of days have the adapters attached?

I am not bad mouthing Nhaler or their service, I am just troubled that the unit did not come as promised and that I cannot get it resolved.
 

Capt.Louisville

Vaping Master
ECF Veteran
Verified Member
May 4, 2011
3,658
5,474
Louisville, KY
Hi MSs, welcome to the LOD (Land Of Darwinia). Nice doghouse, there...

Panky: !!!

Capt: After the first few days, I made sure to get some low-nic juice, because I liked Darwin so much. You know, for safety's
sake.

I can see that will be a problem. Thanks for looking out.
 

Panky

Ultra Member
ECF Veteran
Verified Member
Apr 12, 2011
2,589
2,836
Miami
problem is that I did not get one at all. Even if It had been in there, that would have been fine.

Oh I see. The only time I use mine is for certain attys like the IKV 306 where my cannon tip won't allow me to close the arm. The attys that I have from nhaler are fine though because the cannon doesn't go down more than about halfway :D
 

paulc35

Super Member
ECF Veteran
Jul 24, 2010
314
83
Mason,Wv
Right where the atty/carto screws in, there are four tiny slots, in the top of the plastic collar. i have read of some using a Dremel, but that seems like it would be too sloppy with me using it. Remove the bottle/needle, dry it out as good as you can, and use the hacksaw, and gently pull it through there. I didn't cut even a 1/16" of an inch. Be sure to blow out/clean the little plastic chips you have generated.

There is a little inverted funnel up in there, to help guide the needle in. I insert it carefully, rotating it back and forth to help it find it's way. I also put a piece of Scotch tape down the side, leaving a little tail at the bottom. It helps to pull the bottle out. On a review/discussion thread about the Boge Rev 2.1 someone posted a link for a replacement needle/bottle assembly.

When I ordered my Darwin I got a 510>Ego type adapter and never take it off. Air flow is fine plus it allows me to use regular threaded 510 attys and cartos, or if I want to use the new mega ego cartomizers, which I do alot it screws right on to the threads
on the outside of the adapter..This is a very useful adapter..
 

Drewsworld

Resting In Peace
Mar 14, 2009
6,394
1,029
New Jersey
www.nhaler.com
problem is that I did not get one at all. Even if It had been in there, that would have been fine.

Sorry for not replying sooner....I havent recieved any emails talking about this....I will check later when the guys get in.
However , we didnt send any out without the adapters on the past two shipments...It's the silver piece that is screwed into the brass arm. It wont come off without pliers or some tool. Its only a quater inch or so long.
If your sure it isnt on there , send us an email to DGliem00@gmail.com and I wil take care of it. Thanks
Drew
 

the ob

Unregistered Supplier
ECF Veteran
Jan 31, 2011
7,577
12,011
Portlandia
Sorry for not replying sooner....I havent recieved any emails talking about this....I will check later when the guys get in.
However , we didnt send any out without the adapters on the past two shipments...It's the silver piece that is screwed into the brass arm. It wont come off without pliers or some tool. Its only a quater inch or so long.
If your sure it isnt on there , send us an email to DGliem00@gmail.com and I wil take care of it. Thanks
Drew


Drew,
I apoligize. I am a complete idiot (or a newbie that has not yet figured everything out) You are correct that both models have them attached.

I was not aware that the silver part WAS the 510-510 extension. I assumed that was the 510 and that another piece just like it would be added. When I looked at the piece on your site, it looked the same, but I just assumed that another would be screwed on top.

As I said before you have a excellent reputation for service and I can certainly see why. I am sorry for the posts and as I said in the beginning, my only excuse is that I am an idiot. Thanks for the reply! If I knew how to add it, this would be the place for the embarrassed smiley face icon............
 
Last edited:

Katdarling

I'm still here on ECF... sort of. ;)
Supporting Member
ECF Veteran
Verified Member
Jan 25, 2011
32,594
167,890
Utopia
2da73841.jpg
 
Status
Not open for further replies.

Users who are viewing this thread