Sorry my fault should have mentioned that. Thanks
oh, ok thanks, was kinda confused there
- Status
I am using a variant of these methods right now. Instead of making the wick go through my mesh roll, I just make it go over the mesh and coil so its not wrapped in the coil at all, it feeds the mesh with a good amount of juice and eliminated the leaking issues I had with the mesh alone. Using this method with Gorilla Juice right now. Its the first time I ever enjoy GJ in my ody, this and boba's had always been non-ody juices in my book, but thats all in the past now. And it is also the biggest and tastiest clouds of vapors I ever achieved on my ody, I never tought 3.7v could make me choke! I hope this coil never dies.
Ill post pictures after I finish this tank.
Ill post pictures after I finish this tank.
Yes it would be nice if you post some pics Soda, it sounds interesting and I'll try that too.
Looks good, going to try that out! (Pictures work if right clicked->Open in new tab)
I had the mesh only running in short mode with almost no problems (ok for the first try I guess) but the liquid pressure seems to be too high in big mode. I hope this works as I really like to have mesh in my Ody
I had the mesh only running in short mode with almost no problems (ok for the first try I guess) but the liquid pressure seems to be too high in big mode. I hope this works as I really like to have mesh in my Ody
Yep got it thanks. Looks good, however that wick looks like it's not touching the coil
yes short enough that the wick fits in just okay in the channel, i didnt have to ram the mouthpiece over it. Its pretty much exactly like captsteve's just with a wick slapped on top. The wick does touch the coil there, barely. I did this because with the mesh only, using thin juice (highbrow pv/vg mix), I would have trouble with my juice flow. Sometimes I got dry burns, and if I unscrewed mouthpiece too much, there would be leaking. Maybe I used too little mesh, maybe krinkle's method is only meant to be used with xc-116 wick. It seemed to me like the little piece of mesh would just flood too quick.
First thing I did was put two little pieces of wick in the empty channels to help regulate juice flow. To help feeding the juice up to the mesh without having to open juice control too much causing leaks. It made it a bit better, but it was still a little leaky. Thats when I tried this last method which works just superbly right now. The wick over the mesh really helps retention of larger amounts of juice around the coil and also if the mesh is flooded the extra liquid is absorbed by the wick instead of ending up in your collector tank.
Been vaping my ody non-stop since last night and never got leaking, never got a dry hit and the vapor amount is really impressive. Best results I ever had with my ody.
First thing I did was put two little pieces of wick in the empty channels to help regulate juice flow. To help feeding the juice up to the mesh without having to open juice control too much causing leaks. It made it a bit better, but it was still a little leaky. Thats when I tried this last method which works just superbly right now. The wick over the mesh really helps retention of larger amounts of juice around the coil and also if the mesh is flooded the extra liquid is absorbed by the wick instead of ending up in your collector tank.
Been vaping my ody non-stop since last night and never got leaking, never got a dry hit and the vapor amount is really impressive. Best results I ever had with my ody.
Try putting the extra wick under the mesh instead... and really the only reason you would get any leaking is because the mesh isnt big enough to act as a juice dam at the ceramics channels... you could try just using more mesh or what your doing now or by putting the extra wick under the mesh...
10mm X 40mm works best for me. I Been doing this for awhile now. Think i posted my test runs some time back in the ody official thread. anything lesser then 20mm rolled gives me inconsistent results.
The more mesh material the more juice gets welled up leads to insane vapor production. Not to mention taste
To add, A dry burn plus a quick dip into water cleans it up real nice for a new tank of juice.
The more mesh material the more juice gets welled up leads to insane vapor production. Not to mention taste
To add, A dry burn plus a quick dip into water cleans it up real nice for a new tank of juice.
Madshock, sounds interesting. Sorry but I missed your results when you posted them, do you use like MrK only mesh and no wick or do you use a combo. Can you elaborate for my benefit. Thanks
Mesh only. i started out with wick core tho.
Never used wicks since then. LOL
The denser your mesh is the more it soaks up the juice the more vapor it produces. Try it.
the only thing you need to really take care of when u make a mesh only is to make sure its thick and long enuff to fill up the wick channel like Mr Krinkles short wick. Otherwise it allows the juice to freely flow thru.
Never used wicks since then. LOL
The denser your mesh is the more it soaks up the juice the more vapor it produces. Try it.
the only thing you need to really take care of when u make a mesh only is to make sure its thick and long enuff to fill up the wick channel like Mr Krinkles short wick. Otherwise it allows the juice to freely flow thru.
Great thanks will try it. So you just cut a piece of 10mm x 40mm and roll it up and that as a roll should fit just right, correct? much appreciated
Yeap, pretty much what u did back there. roll it till its snug. And make sure with the coil u sit it all the way to the bottom.
Mine sat in there for abt 3 weeks or so, same coil same wick. It takes awhile to roll a 40mm till it fits btw.
Last edited:
- Status
Similar threads
