VaporShark rDNA
- Thread starter ClintS
- Start date
- th_trl_thread_readers 0
- Status
What grommet fix is this? A quick search didn't show anything, but I am crippled with TapyTalk...
Bits scrambled by Tapatalk...
This is the o-ring fix.
This is the other fix- If you have a Protank, Kanger head -
Use the top (thick part)- take the screw out, slip that rubber piece on & screw it back in.
I've found this to be true. The flavors that come out of some juices very greatly based on temperature.
Bits scrambled by Tapatalk...
I thought they had a wattage range printed on the coil. When it comes to temp protection, it depends on how safe you think your juice and wick are at your pre determined temp setting??!!
Lawl. I'm trying to get back to contact coils with Ni200, and torching them has made it workable. :/
Burping out loud using Tapatalk
Burping out loud using Tapatalk
Well, I finally received my VS on Friday and immediately attached my Kayfun with a kanthal build just to make sure it functioned. All good. Next, first attempt at a nickel build. Since I order on 12/6 I had plenty of time to read up and watch videos on the dna40, nickel builds and temp sensing. Frankly I had become a bit intimidated but jumped right in to the build.
I had played with spaced coils using a screw as well as on a building rod but primarily have been doing contact coils. Not sure what the screw size that I have but its in the neighborhood of 3mm. 9 wraps came out to .17 on my magma clone. Let sit for about 20 minutes and put it on the VS to give it a try. I was very surprised that my first attempt turned out so well. Very impressed with temp sensing. No more burnt wicks. I'm a happy camper!
Next the Kayfun. Did the same build but was a little concerned that it may be too big to fit the chimney on. It fit. Again it turned at better than expected. I did start seeing really poor performance on the Kayfun after the second tank. Decided to open it up to see what was going on and found that my wick was bone dry. Not sure why I started having wicking problems after 2 tanks but I got to see temp sensing in action - no burnt wick!
I guess what I'm trying to get across is to just jump in with both feet. You'll likely do better than you think. And if you mess up its not the end of the world. Rip it out and try again.
I had played with spaced coils using a screw as well as on a building rod but primarily have been doing contact coils. Not sure what the screw size that I have but its in the neighborhood of 3mm. 9 wraps came out to .17 on my magma clone. Let sit for about 20 minutes and put it on the VS to give it a try. I was very surprised that my first attempt turned out so well. Very impressed with temp sensing. No more burnt wicks. I'm a happy camper!
Next the Kayfun. Did the same build but was a little concerned that it may be too big to fit the chimney on. It fit. Again it turned at better than expected. I did start seeing really poor performance on the Kayfun after the second tank. Decided to open it up to see what was going on and found that my wick was bone dry. Not sure why I started having wicking problems after 2 tanks but I got to see temp sensing in action - no burnt wick!
I guess what I'm trying to get across is to just jump in with both feet. You'll likely do better than you think. And if you mess up its not the end of the world. Rip it out and try again.
Last edited:
Not a rDNA but a Vapor Shark nonetheless 
Vaping around the tallest building in the world
Vaping around the tallest building in the world
I'm culturally ignorant when it comes to this, I mean, is vaping generally socially acceptable in the Arab world in general? The UAE, specifically? I'm not tryin' to start anything, I'm genuinely curious. Great shots, regardless! The Burj Khalifa is a stunning piece of architecture!!
This is the o-ring fix.
This is the other fix- If you have a Protank, Kanger head -
Use the top (thick part)- take the screw out, slip that rubber piece on & screw it back in.
From my experience its easier and more stable to put the oring on the positive pin that connects to your mod not the screw inside the actual lemo.
so update on the paint fail of VS.
might consider just getting rid off the whole paint thing and make this a stainless looking shark.
might consider just getting rid off the whole paint thing and make this a stainless looking shark.
I'm culturally ignorant when it comes to this, I mean, is vaping generally socially acceptable in the Arab world in general? The UAE, specifically? I'm not tryin' to start anything, I'm genuinely curious. Great shots, regardless! The Burj Khalifa is a stunning piece of architecture!!
Ah thanks! It is the same as elsewhere buddy ~ BP & BT on the play, dousing disinformation. There are many vapers here as well ~ met a few over lunch on Sunday
It's ok to vape where 'smoking' is permitted.- Status
