Seriously? They aren't going to be happy unless someone sets themselves on fire when their 18650s go up in smoke are they?
WISMEC Reuleaux RX200 TC
- Thread starter USMCotaku
- Start date
- th_trl_thread_readers 0
- Status
0.32 ohms, 9v @ 27.8A = 250 watts output... While the battery would need to put out at least 10.9v @ 23A for a 250 watt drain. So yes, it is possible with high efficiency.
I have no need to upgrade for wattage other than making sure I'm current... can anyone confirm that the only difference with this upgrade is the jump to 250W? Or is there anything else added/changed?
Just out of curiosity, does it now do 200-250 in [ed: 0.1w] increments or is the jump something else? I never vape that high anyway. I'm pushing it now at 80.
Last edited:
Sorry, that's what I meant! not 1, 0.1. Thanks. I'll probably just wait for the next update...
well... just upgraded from 3.00 to 3.10 and default TCR for Ti seems to be a lot worse than before.
kept hitting temp protection ridiculously quick and was responding like crap.
decided to use manual TCR mode and set it to 366 (what steam-engine showed) and it's working like it was prior to update. i figured the update would fix the default tcr... nope. it's worse.
kept hitting temp protection ridiculously quick and was responding like crap.
decided to use manual TCR mode and set it to 366 (what steam-engine showed) and it's working like it was prior to update. i figured the update would fix the default tcr... nope. it's worse.
Heads up you RX200 users. Firmware upgrade to 250w (I haven't tested this)
Reuleaux RX200 Upgrade Firmware 3.10 Version Launching - Wismec Electronics Co.,Ltd
Reuleaux RX200 Upgrade Firmware 3.10 Version Launching - Wismec Electronics Co.,Ltd
anyone else having the same problems with using temp control with default values? tempted to downgrade back down to 3.00, but manual TCR seems to be the best option anyway.
They need to start to include a change log. If the extra 50W is the only difference im staying with the 3.0.
I fully agree. I have no interest in 250w, but it would be good to know if any other changes have been made.
Sent from my M7_PLUS using Tapatalk
Well those of us using tc, it erased my memory presets (easy fix lol) and defaulted to 250 watts in tc. I caught that right before I went to vape it, bet it would have hit temp protect lightning fast.
Could be my imagination but seems with the same manual tcr it isn't going into temp protection nearly as much as it was. I haven't used the factory settings in a long time so can't say if they are better or worse. Nice to see a manufacturer actually continuing to update compared to ipv etc....
Could be my imagination but seems with the same manual tcr it isn't going into temp protection nearly as much as it was. I haven't used the factory settings in a long time so can't say if they are better or worse. Nice to see a manufacturer actually continuing to update compared to ipv etc....
yea.. factory settings for Ti certainly suck more than what it was in 3.00.
using manual TCR has been a lot nicer since i was pretty much forced off the factory settings and into using that. not too horrible i guess, but you'd figure they would pay attention more to functionality than waging in the wattage wars.
using manual TCR has been a lot nicer since i was pretty much forced off the factory settings and into using that. not too horrible i guess, but you'd figure they would pay attention more to functionality than waging in the wattage wars.
It completely resets the device which restores the defaults, (including screen orientation and stealth mode off), and erases stored TCR's. For some reason the default setting is 235 C in TC Ni mode, and full power, (now 250W).
I don't know if they changed anything apart from max power output. I've just been using kanthal.
Upgraded both now I must find instructions again on how to set them up again, one thing is for sure it has bought this thread back to life again
- Status
Similar threads
