Youde Goblin
- Thread starter dravell
- Start date
- th_trl_thread_readers 0
- Status
Thanks for the heads up. As short as looks, if they made a wider deck the capacity would only be maybe 2ml. As much hassle it is break out the screw driver to refill, I would probably just go with my drippers.First thing I'll say right off the bat, this thing makes the Atlantis feel constricted lol.
The deck is VERY small though, going to have to find what builds will work best in such confined quarters.
Last edited:
Okay so...
The flavor is actually pretty good for the amount of airflow this has. The vape is very wet, which I like.
It has the ability to put a very large amount of vapor out, and best of all absolutely no leaking as of yet, even after filling.
I do need to find the best wicking method however. On the couple videos on youtube they are STUFFING their channels. Not sure how their wicking is keeping up like that.
My first time I filled the channels to the bottom, not too tight, just enough to completely fill the channels where the chimney did push down on them a little when screwing it down (theirs pushed down, a lot), it wicked but wouldnt keep up on long drags and or chain vaping at 45+ watts.
I currently trimmed the wicks down a bit so they are filling most of the vertical channel but quite a bit looser in the channels themselves, enough for the chimney to clear them without pushing them down.
This is better but still not keeping up at 45+ watts on chain vaping and/or really long drags. Will keep fiddling until I find the perfect wicking, heat wise this will be able to push 60+ watts no issue, I know the channels will support it.
I really dont know how those guys kept their wicking up though with their channels stuffed that much.
The flavor is actually pretty good for the amount of airflow this has. The vape is very wet, which I like.
It has the ability to put a very large amount of vapor out, and best of all absolutely no leaking as of yet, even after filling.
I do need to find the best wicking method however. On the couple videos on youtube they are STUFFING their channels. Not sure how their wicking is keeping up like that.
My first time I filled the channels to the bottom, not too tight, just enough to completely fill the channels where the chimney did push down on them a little when screwing it down (theirs pushed down, a lot), it wicked but wouldnt keep up on long drags and or chain vaping at 45+ watts.
I currently trimmed the wicks down a bit so they are filling most of the vertical channel but quite a bit looser in the channels themselves, enough for the chimney to clear them without pushing them down.
This is better but still not keeping up at 45+ watts on chain vaping and/or really long drags. Will keep fiddling until I find the perfect wicking, heat wise this will be able to push 60+ watts no issue, I know the channels will support it.
I really dont know how those guys kept their wicking up though with their channels stuffed that much.
Last edited:
I'd agree. I threw a couple of 12 wraps around a 2.4 mm 28 gauge coils in there and am running it at 25 Watts right now. I overworked the channels, only one is bubbling but it's a pretty good vape with 80% VG juice. I'm going to tear it out and rewicK fairly soon but so far, so good.
Last edited:
I think im gonna wick it like I wick my Aqua V2 next. My Aqua V2 wicks everything.
Pics please!
I'm only getting bubbles out of one of the juice wells so I'm definitely not seeing what this thing can do yet.Pics please!
Once this tank goes empty Ill switch out the build and take pics along the way and post em up here for ya.
Okay had to fill another tank before the new build. Its actually wicking good enough to vape at 45w, but I know this tank can handle 60+ watts no problem so a re-wick is going to have to happen. The 3ml goes *really* fast at 45w so wont be long.
Also laid it on its side for a bit to see if it would leak, didnt at all for the time I had it down.
Also laid it on its side for a bit to see if it would leak, didnt at all for the time I had it down.
I didn't have any luck with the rewick, less cotton but the same performance pretty much. I might try this again tonight with a 2 mm mandrel to reduce the amount of cotton in the channels. I think I'll try trimming first.
I hope this isn't a common problem... I have an issue that requires super-max VG joose. That stuff is so thick that 2.5mm is about the only size that doesn't char cotton almost immediately the way I chain vape
Triangle vapes was the only one I saw who had it and they're out of stock. I'm watching for one though because I love my Lemo, but the draw is still too tight.... haven't nutted up to drill one of my two out yet...
Please, Sir. Do share. Inquiring minds would like to know how this is done. Also does this include super-max VG that's uber thick, like Cereal Killah for example.
Thanks fer sharin'!
I hope this isn't a common problem... I have an issue that requires super-max VG joose. That stuff is so thick that 2.5mm is about the only size that doesn't char cotton almost immediately the way I chain vape
Triangle vapes was the only one I saw who had it and they're out of stock. I'm watching for one though because I love my Lemo, but the draw is still too tight.... haven't nutted up to drill one of my two out yet...
You can run 2.5mm on here but anything bigger is going to be hard. If you want to go bigger than 2.5 id suggest the Silverplay.
Thanks dravell! That's good to know. I usually run 2.5mm coils, so now all I need to figure out is which one has more airflow and I'll know which one to get lol!
That's where I'm at too. I emailed UD earlier today with a few questions but if the silverplay has more airflow, I'm heading that direction since, apparently, so many KF parts fit it and I can change the look a bit.
Sent from my iPhone using Tapatalk
I vape pretty thick juice 85%VG/ 5%/Vodka 3%/Nic/PG 7%/Flavor/PG and have no wicking issues on the Aqua 2. I split my wicks so only a small leg fills the channel. I use this method for my Fogger and Orchid. Works great. I don't believe I would have any problem with 100% VG using this method. I imagine I'll use this method for my Goblin too if I can ever get my hands on one.
Last edited:
- Status
