Post pictures of your working wick and coil setup

[Deap]

Anyone actually use the Phenotype-L?

I'd really like a two poster that lets me single could with the right amount of airflow. Also as asked earlier how is it on deck space? I've been contemplating trying 26650 attys just to have the extra space for coils, so deck space is a super top priority... For me...

 

[Braaapp]

Scrap wire builds...
24/32 KA1 clapton tiger'd with 0.8ribbon/40ga. 0.4Ω

24/40ga N80 clapton tigered with 0.8 ribbon 0.2Ω

 

[Tom Forde]

And about the phenotype-L, if you have a TM atty, the TM atty's chamber/cap fits on the pheno and vis versa

 

[kkiet]

All these coil builds are awesome. I could only wish to do something like these.

 

[Retro138]

Anyone actually use the Phenotype-L?

I'd really like a two poster that lets me single could with the right amount of airflow. Also as asked earlier how is it on deck space? I've been contemplating trying 26650 attys just to have the extra space for coils, so deck space is a super top priority... For me...

I used one for a few days and really liked it. My description a page back is from using it and building on it for a couple of days

 

[Tom Forde]

I used one for a few days and really liked it. My description a page back is from using it and building on it for a couple of days

Yeah it looks like a great atty, and I'm sure I could check it out at VVVapes since they carry TM Atty's & anarchist products...I'm still leaning towards a Pugio because of the ability to rotate the center pin and literally drop in your coils. Or a Kennedy 24, because of the added space and the super deep juice well. Why do they always have to come out with awesome atty's just when I think my mind is made up? I already have a couple 2 post atty's with a 1:1 velocity clone my father ordered on the way, he ordered 2 of them, one for me one for him.

 

[Retro138]

Yeah it looks like a great atty, and I'm sure I could check it out at VVVapes since they carry TM Atty's & anarchist products...I'm still leaning towards a Pugio because of the ability to rotate the center pin and literally drop in your coils. Or a Kennedy 24, because of the added space and the super deep juice well. Why do they always have to come out with awesome atty's just when I think my mind is made up? I already have a couple 2 post atty's with a 1:1 velocity clone my father ordered on the way, he ordered 2 of them, one for me one for him.

Say goodbye to my vape "budget"... I want one of everything that comes out for intricate builds. I count at least 10 on the market right now.

 

[Tom Forde]

Say goodbye to my vape "budget"... I want one of everything that comes out for intricate builds. I count at least 10 on the market right now.

Yeah my problem is I need a new mod too lol, still rockin my sig100 without a spring loaded contact

 

[Retro138]

Yeah my problem is I need a new mod too lol, still rockin my sig100 without a spring loaded contact

That Sig is a warhorse homie.

I pulled the trigger on the snow wolf ($85) til the whiteout has time in people's hands, and any bugs there may be worked out and what chipsets I want etc. etc.

The pugio is awesome in concept but looks small for your style of building and the insulator looks strange to me. I do love the way the coils mount.

 

[wvloony]

26g n80 Claptoned with 36g n80 twisted with 28g n80 then fused with 36g 80.

That seriously looks like you made coils with barbed wire. Nice looking coils thats for sure

 

[wvloony]

So here is my first successful attempt at claptons, they are 26ga k1, wrapped with 30ga k1 6 wraps each pushing .5 ohms

 

[Tom Forde]

That Sig is a warhorse homie.

I pulled the trigger on the snow wolf ($85) til the whiteout has time in people's hands, and any bugs there may be worked out and what chipsets I want etc. etc.

The pugio is awesome in concept but looks small for your style of building and the insulator looks strange to me. I do love the way the coils mount.

It looks small, looks being the key word. It can fit massive coils, and if the coils are too found to fit in the slots, I just have to flatten out the leads a bit and build sleepers off one stick of wire. I've seen people put some pretty big coils inside of that atty. I'm gonna pull the trigger on the whiteout once they start shipping and people start receiving products. I've decided to go for the DNA version & to get an extra LiPo and panel kit to start out with. And you're right..my sig100 is a war horse..it's been through every type of weather from snowboarding with me to 100+ degree heat and I've never had a problem with it.
New coil in the hobo too, 3 core 30g/36g alien parallel to 24g N80 on a 3mm bit -

Edit: As for the whiteout I just read some chip specs, the DNA 200 can read down to .08 in power mode & .04 in TC mode. That's better than the sx350j chip out right now. Better than ANY chip out right now. Besides, YiHi is releasing their SX Mini ML class soon, with an SX350J-V2 chip inside it. So I'll pass on an SX350J box now

 

[SLIPPY_EEL]

i also have a sig 100w thats has zero probs.

Heres a dual parallel.
I stepped up my normal 2.5id to 3mm for this one as i knew it was gonna be super low ohms otherwise.
its 20g A1 parallel with 22g 317l, so gives me a slight staged when fired up but the thing lights up so dam fast anyway its hardly noticable(spelling)
0.05ohms.

is a god hot vape that clouds the room quick

I'm using these lower ohm builds on my two Vertex mods that take 3x 18650 so plse dont copy unless you have the equipment and knowledge.

 

[Tom Forde]

i also have a sig 100w thats has zero probs.

Heres a dual parallel.
I stepped up my normal 2.5id to 3mm for this one as i knew it was gonna be super low ohms otherwise.
its 20g A1 parallel with 22g 317l, so gives me a slight staged when fired up but the thing lights up so dam fast anyway its hardly noticable(spelling)
0.05ohms.

is a god hot vape that clouds the room quick

I'm using these lower ohm builds on my two Vertex mods that take 3x 18650 so plse dont copy unless you have the equipment and knowledge.

Yeah I was gonna say unless you're using a parallel or triple parallel box don't even try..but clouds bro... All the DNA 200 preorders are starting to land and they're all over Instagram. And I just found a new mod called the SX Dual...pretty easy to figure out what it is. I can't take it. I just wanna buy something now. Still holding out though but every impulse is shouting "BUY ME BUY ME BUY ME!!"

 

[SLIPPY_EEL]

Yeah I was gonna say unless you're using a parallel or triple parallel box don't even try..but clouds bro... All the DNA 200 preorders are starting to land and they're all over Instagram. And I just found a new mod called the SX Dual...pretty easy to figure out what it is. I can't take it. I just wanna buy something now. Still holding out though but every impulse is shouting "BUY ME BUY ME BUY ME!!"

One of the main reason's i stick to Mechanical mod's is that they are soo so cheap Tom, like the Vertex and takes anything upto 3x18650, raw basics and nothing inside to break

 

[Superfecta_]

I sprouted several grey hairs with the frustration/time involved making these. But success either way. 2x26n80 6x.5ka1 36/38n80.


The framed stapled fused perform a lot better, but these are so sexy.

 

[SLIPPY_EEL]

which is the framed stapled fused? you got a pic?

which part of the build frustrated you super?

when i unwrap one of the two claps from the wire i pull it through the smallest hole in that ruler i posted a little way back with the main wire laying against it, so long as you unwrap say 5mm first the rest comes off a 8inch piece in seconds ... just saying

nice example though mate

 

[Tom Forde]

One of the main reason's i stick to Mechanical mod's is that they are soo so cheap Tom, like the Vertex and takes anything upto 3x18650, raw basics and nothing inside to break

Yeah I agree. I have my AV mod as a single battery, and a Dimitri box mod. Both authentic but I got them cheap. I do have a first run FUhattan mod too. I like the Dos Equis & Cascador mods but right now I want an up to date regulated mod, and the Whiteout is still on schedule to ship at the end of the month. So after I see the first runs go out I'm buying mine. I've decided on the DNA already.

No more prototypes production is going smoothly apparently.

 

[Superfecta_]

which is the framed stapled fused? you got a pic?

which part of the build frustrated you super?

when i unwrap one of the two claps from the wire i pull it through the smallest hole in that ruler i posted a little way back with the main wire laying against it, so long as you unwrap say 5mm first the rest comes off a 8inch piece in seconds ... just saying

nice example though mate

The most frustrating part is just fusing it all together. I could have used like 32 or 34 or something to make it a lot easier, it looks so good with the 38g staggers tho! I want to go full speed, but you can't. I probly reversed the drill to undo missed wraps 100x making enough for 2 coils.

Framed stapled fused is the same build minus the staggers, I just fuse it all together with 40n80 instead of trying to hit all the staggers while fusing.

I'm going to attempt a 14x.5ka1 staple, will report back.

 

[Tmb821]

1/16 26g/32g clapton.