Aga-T wick length and coil wraps?

[dwcraig1]

Finally got around to putting a solid wick in my other AGA-T, 28 Kanthal 4/5 @.9 ohms on my new smok Telescope w/ 18490 AW battery that I purchased just for this super LR stuff, all I can say is WOW, I hope I don't get spoiled by this and want to use it all the time

 

[xbassman]

Finally got around to putting a solid wick in my other AGA-T, 28 Kanthal 4/5 @.9 ohms on my new smok Telescope w/ 18490 AW battery that I purchased just for this super LR stuff, all I can say is WOW, I hope I don't get spoiled by this and want to use it all the time
View attachment 166046

You'll probably do as I did.....
Had mine @ 1.1 ohms, then got a Vamo for Christmas.
It didn't take long for me to recoil my AGA-T over 1.2 ohms so I could use it with my new PV.

Nothing else is getting any love right now.....

 

[dwcraig1]

You'll probably do as I did.....
Had mine @ 1.1 ohms, then got a Vamo for Christmas.
It didn't take long for me to recoil my AGA-T over 1.2 ohms so I could use it with my new PV.

Nothing else is getting any love right now.....

Actually I went just the opposite, I have gone with mechanical from a Zmax, but just for the Gens

 

[xbassman]

Actually I went just the opposite, I have gone with mechanical from a Zmax, but just for the Gens

Well, I wouldn't call that opposite...
AGA-T just won out with all mt different atomizers....
I'll bet it will with yours as well.


Sent from my iPhone using Tapatalk

 

[45root]

Actually I went just the opposite, I have gone with mechanical from a Zmax, but just for the Gens

i have since dropped down to 4/5 wraps and gone mechanical too. lot easier and faster making and adjusting coils. less than 10 minutes using wicks i already have just sitting here. it would be even faster if i could find some washers.

 

[dwcraig1]

I just measured my above set up to see the voltage under load, with 18490 with less than 2 cycles sitting at 4.1 volts it was 3.78 with the .9 ohm load. That translates to 15.86 watts. Great flavor, didn't seem too hot, pretty heavy duty vapor though.

 

[vapdivrr]

Finally got around to putting a solid wick in my other AGA-T, 28 Kanthal 4/5 @.9 ohms on my new Smok Telescope w/ 18490 AW battery that I purchased just for this super LR stuff, all I can say is WOW, I hope I don't get spoiled by this and want to use it all the time
View attachment 166046

thats the way to set up a genny.

 

[dwcraig1]

thats the way to set up a genny.

I learned it mostly from your posts.
Here's under the hood:

 

[mrdee3]

My first coil and wick job.

Sent from my DROID RAZR using Tapatalk 2

 

[vapdivrr]

I learned it mostly from your posts.
Here's under the hood:
View attachment 166299

pretty sweet, next i want to sand off the knurls on the aga-t. mine look like yours, really rough. i think theres another model thats not as rough. theres some posts on making them smooth.

 

[xbassman]

My first coil and wick job.

Sent from my DROID RAZR using Tapatalk 2

Nicely done mrdee!


Sent from my iPhone using Tapatalk

 

[Rule62]

pretty sweet, next i want to sand off the knurls on the aga-t. mine look like yours, really rough. i think theres another model thats not as rough. theres some posts on making them smooth.

I've sanded off the knurls on all 3 of mine. Only took maybe 20 minutes each. Well worth the effort, IMO. Those heavy knurls remind me of high school shop class.

 

[mrdee3]

Now that I got mine set up what is the recommended hole size mine draws a little tight.

Sent from my Nexus 7 using Tapatalk HD

 

[mrdee3]

Nicely done mrdee!


Sent from my iPhone using Tapatalk

Thank you much xbassman

Sent from my Nexus 7 using Tapatalk HD

 

[in4mati0n11]

Now that I got mine set up what is the recommended hole size mine draws a little tight.

Sent from my Nexus 7 using Tapatalk HD

before you go drilling holes, stick a toothpick through or wipe inside cap. condensation sometimes makes my draw stiff.

 

[vapdivrr]

I've sanded off the knurls on all 3 of mine. Only took maybe 20 minutes each. Well worth the effort, IMO. Those heavy knurls remind me of high school shop class.

melbourne is there some specific ways that you did it? perhaps a video you saw. thanks

 

[jkim5708]

I just received and want to know what dimensions people are cutting there ss meshes...first i need to sand down the cap to get air hole aligned

 

[in4mati0n11]

I just received and want to know what dimensions people are cutting there ss meshes...first i need to sand down the cap to get air hole aligned

Have you tried disassembly and reassembly to make sure the tank isn't on too tight or too loose? This affects where the airhole lines up..

 

[dwcraig1]

I just received and want to know what dimensions people are cutting there ss meshes...first i need to sand down the cap to get air hole aligned

For a solid wick for the AGA-T 4"x1.75"
might have to trim a little as 1 3/4" is just a fuzz too tall

 

[arh32]

Mine will be here tomm!! What about for a wick with a hole. What is a good width for that to start with ?