70/30(pg/vg), 15mg nic. Very pleasant vape. Plenty of flavor. Nothing overbearing about it. Vapes beautifully in the Prime at 430 degrees. Just my opinion.
Authentic Svoemesto Kayfun Prime
- Thread starter Bronze
- Start date
- th_trl_thread_readers 0
- Status
What tip are you gonna use on the wave? Are you getting the top that allows you to use any tip? I had gotten that part or perhaps it came with it, but then purchased the special DT (forgot the part number but they make a few different sizes). With the special DT, it makes it very compact
Sent from my SM-G960U using Tapatalk
I use DF at 60 to 70vg and always 24mg. Its extremely clean juice and is not a bunker and very smooth imo. I buy it 100mls at a time and add a flavor shot, awesome juice
Sent from my SM-G960U using Tapatalk
What tip are you gonna use on the wave? Are you getting the top that allows you to use any tip? I had gotten that part or perhaps it came with it, but then purchased the special DT (forgot the part number but they make a few different sizes). With the special DT, it makes it very compact
Sent from my SM-G960U using Tapatalk
I think the description said it was coming with the top nut for any drip tip
Sent from my iPhone using Tapatalk
That's good ....I used that for a while, but I think it looks a bit more streamline with just a tip. As with all ST's tanks, dont over tighten, as the way it threads onto the metal part is kind of delicate, but once you get use to it, its sturdy and a beautiful tank.
Sent from my SM-G960U using Tapatalk
I have ST tanks for my V3 that I bought directly from them, happy to be getting their tank from the United States! Quicker delivery [emoji4]
Sent from my iPhone using Tapatalk
Oh ok , then you know and it's pretty much the same. I have a couple for my km3's and I dont think I was ever able to find a US vendor, is it origin vapes or vaping art?
Sent from my SM-G960U using Tapatalk
I’m glad I noticed the tank was cracking, we’re flying on the 23rd. I would have had another setup with me but it would been a bummer.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
CDV has the Prime nite in stock. I just placed my ordered. Now I get to sit back and wait about two weeks for it to show up.
Just FYI, it appears that Origin Vape has it also. Wish I knew that, before I placed this order.
This may seem a little obvious, but for those who are not getting perhaps the flavor or think wicking is a bit off, have you simply looked at your wick by accessing it at any time? any time, whether its before or after a vape, first thing in the morning, etc, access the deck and look at the wick , it should always be glistening and totally saturated . Every now and then I will rewick and after the first few vapes, I know something is a bit off and usually its because my tails are a tad too long or too bushy and when I open her up, the first thing I notice is my wick doesn't look 100 percent wet and shiny. I'm sure this is the first thing most look at , but sometimes the simplest thing gives the best feedback....
Sent from my SM-G960U using Tapatalk
Sent from my SM-G960U using Tapatalk
I also ordered from CDV this morning, they shipped it already!!
Sent from my iPhone using Tapatalk
will these fit the KFL+?
according to FT they're meant for the mini V3.
they seem a bit thick but it may be the close up picture
and i have no idea if the hole is the right size and would make a tight seal around the center pin.
according to FT they're meant for the mini V3.
they seem a bit thick but it may be the close up picture
and i have no idea if the hole is the right size and would make a tight seal around the center pin.
I can't say for certain, but I doubt it. I suspect the V3 and KFL+ are likely to have different designs for that part.
So the question might be, does the km3's insulator fit the kayfun light plus? If no one knows off hand, I can take apart and find out
Sent from my SM-G960U using Tapatalk
OK, let me take a look. I think I have some of those in my bone box somewhere. I mean, we're supposed to help each other, right?
The V3 is ever so slightly smaller than the KFL+. But the V3 insulator does drop into the hole on the KFL+. So it just might work.
I wont tell you what I would have called my wife if she asked.
I wont tell you what I would have called my wife if she asked.
Thanks guys i appreciate it and the effort taken getting those pieces out of their boxes
i might just order one since it's around 2$ and and see for myself as these insulators are hard to find and usually quit expensive.
i might just order one since it's around 2$ and and see for myself as these insulators are hard to find and usually quit expensive.
- Status
