Eleaf Lemo II

[sbmqcy]

I'm having issues with my lemo 2 and titanium wire. I'm using 26a wire. I just received my lemon, and I cannot get my resistance to remain stable. It's jumping around, way higher than it should be based on the wire and wraps. I wrapped 6 wraps on a 7/64 drill bit (~3mm). The res is jumping around like crazy on both a little res checker box as well as on my evic-vt. Is this something that others have found/is there something basic I'm missing? Alternatively, can someone point me to a really good build guide for these so I can maybe discover what I was doing wrong? Unfortunately, I'm at work now and can't take any pics to show what my build looks like.

I trapped the wires under the screws (trapping in the holes was even worse, as far as wandering resistance goes). Help!

 

[SteamHead]

We went to the beach, and ever since then my girl's Lemo2 has been giving a "No Attomizer" error, both on her iStick30 and my Zero clone 50w. Any idea what could've happened, and what I should be looking for? Coil seems tight and fine, I've cleaned both the threads on the bases, even pushed the positive pin out a bit, no dice.

 

[nancybout]

Will it work on the evic?


Sent from my iPhone using Tapatalk

 

[1MEANGT]

Couldn't hold out any longer. Just ordered one.

 

[sbmqcy]

I'm having issues with my lemo 2 and titanium wire. I'm using 26a wire. I just received my lemon, and I cannot get my resistance to remain stable. It's jumping around, way higher than it should be based on the wire and wraps. I wrapped 6 wraps on a 7/64 drill bit (~3mm). The res is jumping around like crazy on both a little res checker box as well as on my evic-vt. Is this something that others have found/is there something basic I'm missing? Alternatively, can someone point me to a really good build guide for these so I can maybe discover what I was doing wrong? Unfortunately, I'm at work now and can't take any pics to show what my build looks like.

I trapped the wires under the screws (trapping in the holes was even worse, as far as wandering resistance goes). Help!

I think I got it squared away. I unscrewed the center pin and reseated the positive post and screwed it back down well.

Will it work on the evic?


Sent from my iPhone using Tapatalk

Yep, it's working fine on my evic vt now. 7 wraps on 7/64 drill bit. .31 ohms.



Sent from my mobile

 

[ArgusMcJohnsten]

Super silly question. I've got some money to waste, so I'm looking at picking one of these up, but it's listed as "eleaf Lemo 2 Sub Ohm tank Set" can I do non sub ohm on it? I'm still very new, but so far it seems like I'm liking 1.2-1.5 range the best. My only mod is a vamo v7, so I can't go under 1 ohm anyway.

 

[KTMRider]

Super silly question. I've got some money to waste, so I'm looking at picking one of these up, but it's listed as "Eleaf Lemo 2 Sub Ohm Tank Set" can I do non sub ohm on it? I'm still very new, but so far it seems like I'm liking 1.2-1.5 range the best. My only mod is a vamo v7, so I can't go under 1 ohm anyway.

You'll be fine with it. "Sub-ohm" is a marketing term for the cool kids (or wanna-be's).

 

[ArgusMcJohnsten]

Thanks. I placed the order. Now I feel like another mod since I'll have 2 attys

Love the trooper on a pooper.

 

[Azarias]

Thanks. I placed the order. Now I feel like another mod since I'll have 2 attys

Love the trooper on a pooper.

I hear you. I can't stand having more mods than attys or vice versa

For future purchases. It seems that nowadays every atty with an open draw is called Sub-Ohm tank. But you can use pretty much every of this attys for M2L too.

 

[SteamHead]

We went to the beach, and ever since then my girl's Lemo2 has been giving a "No Attomizer" error, both on her iStick30 and my Zero clone 50w. Any idea what could've happened, and what I should be looking for? Coil seems tight and fine, I've cleaned both the threads on the bases, even pushed the positive pin out a bit, no dice.

Anyone?

 

[jackmormon]

Anyone?

I have had inconsistencies with the Lemo2 & its 510 pin. A quick thing you can try is remove the base and use something like a chopstick to push out the 510 pin and the insulator. Wash both off, they may have juice stuck to them. Also clean the area where the 510 insulator goes into the base. Use the chopstick to reseat the 510 insulator. You will know it is seated because you can't push it in any further.

Now the important part.... Re-attach the base to to the atomizer before putting the 510 pin back in. Lightly push it in. It will make a plop type sound when it is seated. Do not force it or hammer on it or anything.

I don't have either of the mods you mentioned but with an SX Mini that has a very strong 510 pin I have to periodically remove the Lemo, pull the 510 pin out about a little bit and re-attach to the mod. The tension in the Mini's 510 connector seats it perfectly when I do this. It seems like too much pressure on the 510 pin on the Lemo2 is what gives erratic resistance / misreads. (At least for me.)

 

[Hanha]

Anyone?

Sand/file down both the screw slot and the bottom pin. I think if there are even little roughness it will not connect that good.

Two of my Lemos did fall to the floor and no connection. Filed both ends so there was a good contact, nothing else worked.

 

[Will P.C.]

Had this tank about a month now and absolutely love it. I feel like it was specifically made for me! Vaping at .6 with 24 gauge 3mm inner diameter. kanthal and ... cotten. Nice flavor and clouds with no dry hits. I am usually at 3.8-4.0 volts. I was a dripper before this tank.

I wick it very fast/ sloppy the way pbasardo shows in his video. I also am pretty rough with the tank leaving it in my cargo shorts and various positions in house/car wih no leaking.

 

[VaPreis]

Anyone?

My wife dropped her Lemo 2 and it had the same issue afterwards. I ended up disassembling the base. I flipped the white circular insulator that goes around the pin inside the deck, reassembled it, and it's been working fine since.

 

[Bikenstein]

No problem for 2 months with the Lemo 2 and SX MIni M combo in TC or regular power mode.

 

[pany]

For those who have tried different setups, which is considered the best with 26awg wire and 2.5mm dril? Currently i am running 5 warps at 0.7ohms and i am wondering if i can get better results with higher onms.

 

[HDMontana]

Why is my my Lemo 2 not working correctly? All of a sudden, the juice is not feeding enough through. I have been using it a month now with no problems. Refilled tank this morning, and now I have to block air holes and take primer pulls to get the wick to stay saturated, otherwise it starts to set off the dry wick notification on my IPV4. I drained it and juice holes are not blocked. Plenty of wick and a 3mm coil. Was working great until the refill this morning. Same juice as well. Anyone have any ideas? Thank you.

HD

 

[Firecrow]

Re-wick, it could be twisted or messed up somehow on the inside and not drawing properly. Had that problem - the L2 seems to be sensitive to wicking for some reason.

 

[HolmanGT]

I have found that I have to keep the wick well away from the juice ports. If I do that and get it right I will see fairly regular air bubbles coming up. Of course the problem gets worse with things like Max VG juices.

I use rayon for my wicks and if I keep the holes clear with 50/50 I get great results. With 20 Pg / 80 VG I have to sometime tip the Atty horizontal to get a few bubbles to come up. When I am using the thick juice I will do the horizontal tip every 15 to 20 puffs.

 

[jcmcphail]

I had similar issues, found that tank was assembled to tight, I loosened tank till glass would just about turn and started wicking again.