Νο...invalid information!!! I'll edit my posts.
I just check it again with another Ihaka's rebuildable!!!
The previous must been faulty
I just check it again with another Ihaka's rebuildable!!!
The previous must been faulty
GG compatibility & tips and tricks
- Thread starter D Stanley Querfurth
- Start date
- th_trl_thread_readers 0
- Status
Imagine that I had Vasilis for a witness the day before yesterday
He couldn't understand it either
He couldn't understand it either
big thx stelioss i will edit the first post
thx to Itshak, who was right
thx to aal who will tell me a second opinion ,before i edit post 1
stan
how long will it look out, can it be managed by using the ggts connector and telescope ?
Sure aalwani
Only by cutting it with a dremel as I did in my Ody-Ithaka
Anyway... we can not say that Ody drip mode base is compatible with Ithaka's rebuildable
Only by cutting it with a dremel as I did in my Ody-Ithaka
Anyway... we can not say that Ody drip mode base is compatible with Ithaka's rebuildable
Sure aalwani
Only by cutting it with a dremel as I did in my Ody-Ithaka
Anyway... we can not say that Ody drip mode base is compatible with Ithaka's rebuildable
lol- long way to go- it is like its name ---> ODY Drip Mode BASE----- not ODY/ITHKAK drip mode base ---lol
it's not good idea after all sorry guys.
I don't see reason for using this when
Ithaka spider dripp kit is availble,it will give much better alternative.
and it's the correct way to go for Ithaka users and for
Ody users ( with adding Ithaka upper tank part)
GG spideR is the best dripper provideR
add: better to go all steel tank for using it as a dripper IMO
I don't see reason for using this when
Ithaka spider dripp kit is availble,it will give much better alternative.
and it's the correct way to go for Ithaka users and for
Ody users ( with adding Ithaka upper tank part)
GG spideR is the best dripper provideR
add: better to go all steel tank for using it as a dripper IMO
Last edited:
If not cut it will be too long even for the JGG lid, it will push out the axis of the lid too much which will throw the JGG pin outside collector tank. One time I made it work, but it was inside UFS. because ggts you need the 801-510 adapter so you will have same problem as JGG.
edit my post:
I think you will need this Ody base drip mode:
THE GOLDEN GREEK MODS :: Odysseus Accessories :: Odysseus Base 510 Drip Mode - e-smokeguru
if u fit Ithaka old atty inside you can screw the ody drip cap on!
(the inside threads are the same for Ody atty and old Ithaka atty)
sorry michob123 it's not the best solution after all,
as you need to cut the center post of Ithaka as it's too long.
new edit:
if one looking for GG dripper most easy way to go now will be just adding
the new dripp mode kit,to the tank you allready have.
I think you will need this Ody base drip mode:
THE GOLDEN GREEK MODS :: Odysseus Accessories :: Odysseus Base 510 Drip Mode - e-smokeguru
if u fit Ithaka old atty inside you can screw the ody drip cap on!
(the inside threads are the same for Ody atty and old Ithaka atty)
sorry michob123 it's not the best solution after all,
as you need to cut the center post of Ithaka as it's too long.
new edit:
if one looking for GG dripper most easy way to go now will be just adding
the new dripp mode kit,to the tank you allready have.
Last edited:
it's not good idea after all sorry guys.
I don't see reason for using this when
Ithaka spider dripp kit is availble,it will give much better alternative.
and it's the correct way to go for Ithaka users and for
Ody users ( with adding Ithaka upper tank part)
GG spideR is the best dripper provideR
add: better to go all steel tank for using it as a dripper IMO
It's ok Itshak... after all we just check the compatibility here
I try it and leaves the JGG Lid's Brass Center Pin handling with one of his o-rings!
Then maybe we put off the center pin of the lid and also raise the AD pin of collector tank Stelios?
It's ok Itshak... after all we just check the compatibility here
I try it and leaves the JGG Lid's Brass Center Pin handling with one of his o-rings!
The best modification to do,if one don't have the spider dripper kit.
and the brass is even more easy to cut then SS center post.
I think Ithaka atty will give better airflow and more option for setup if one prefer use silica,
as wick in a dripper.
We have also two inside nuts hight to choose from,so we control the TH to some extend.
And more juice capacity holding Maybe??
Not enough to touch BUT we can also add the Ithaka's adjustable pin and... Yeaaah!!
Not enough to touch BUT we can also add the Ithaka's adjustable pin and... Yeaaah!!
And you could even add penelop v2 new brass pin to ithaka brass pin to make it even longer !!!
If you mean Penelope V2 center post ad pin... it doesn't fit... We have a Ithaka's center post here!
aaaaaaaaaahh Ok ... You mean on the Ithaka's center post ad pin!!!!!!!!!
Ok.... we are crazy indead
aaaaaaaaaahh Ok ... You mean on the Ithaka's center post ad pin!!!!!!!!!
Ok.... we are crazy indead
- Status
