GP Series by VapourArt - Official Thread for GP Spheroid, GP PAPS, X, GP Piccolo, GP SnP and more - Part 2
- Thread starter perseas
- Start date
- th_trl_thread_readers 0
- Status
If it is a prometey 2, then yes it is. If so, want to let it go?
any word on vapourday for the new spheroid?
Sent from my iPad using Tapatalk
Sent from my iPad using Tapatalk
Okay, so my first build with the Koh Gen Do wasn't fancy. Simply to compare similar builds with a new wick in the Heron.
My coil is a 28ga 7/8 wrap 2.4mm mini coil. It's hovering between 1.3 and 1.4 ohms. I normally pull one full strand of SnC through the coil to get a full loop to put through the cotton topper and this is my standard setup.
This time, I cut one wick strand (along the long edge of the KGD pad) between 2 and 3mm wide and proceeded to loop and pull as normal.
Verdict? Works great! No break in time needed and wicks faster, with better vape saturation than the SnC, but only by the smallest of margins.
This might be all in my head but I do believe that the KGD produces a bit more vapor than my comparable SnC setup.
So, the results are close but further testing is needed to see how this wick holds up for me. I vape rather clear liquids so I don't gunk up very quickly but we'll see.
I think where the KGD wins is:
1. I don't have to boil it and it remains mighty fluffy through installation and use so far.
2. I designed my coil size around the SnC so I could pull a full strand through to make my single loop. Because the KGD can be cut so easily to size I think it's more flexible for my coil building so that I can pull the full loop (with smaller diameter wick) through a smaller coil and still maintain my wick's shape with loop.
3. I've never been very consistent in wick size when pulling cotton from ball. KGD gives me much more repeatable, consistent results and it's a breeze to size and cut.
I'm liking it initially.we'll see how this wick performs through a few more tanks...
My coil is a 28ga 7/8 wrap 2.4mm mini coil. It's hovering between 1.3 and 1.4 ohms. I normally pull one full strand of SnC through the coil to get a full loop to put through the cotton topper and this is my standard setup.
This time, I cut one wick strand (along the long edge of the KGD pad) between 2 and 3mm wide and proceeded to loop and pull as normal.
Verdict? Works great! No break in time needed and wicks faster, with better vape saturation than the SnC, but only by the smallest of margins.
This might be all in my head but I do believe that the KGD produces a bit more vapor than my comparable SnC setup.
So, the results are close but further testing is needed to see how this wick holds up for me. I vape rather clear liquids so I don't gunk up very quickly but we'll see.
I think where the KGD wins is:
1. I don't have to boil it and it remains mighty fluffy through installation and use so far.
2. I designed my coil size around the SnC so I could pull a full strand through to make my single loop. Because the KGD can be cut so easily to size I think it's more flexible for my coil building so that I can pull the full loop (with smaller diameter wick) through a smaller coil and still maintain my wick's shape with loop.
3. I've never been very consistent in wick size when pulling cotton from ball. KGD gives me much more repeatable, consistent results and it's a breeze to size and cut.
I'm liking it initially.we'll see how this wick performs through a few more tanks...
Last edited:
If it is a prometey 2, then yes it is. If so, want to let it go?
I think this is the Prometey 1. It has the odd shaped bottom.
I have a bottom ring to give it a uniformed appearance.
I think I will hold on to this for a while.
Last edited:
It's getting confusing because this is the Prometey II but on the website they have now changed it to PROMETEY.
BTW... I know a lot of people are on the KGD spree right now and are getting/have gotten their supply in.
Since I don't believe you can get them locally, if there any locals on here that want to try it out, send me a PM and I'll drop a pad, or two, in the mail for y'all. (unless I run out, I guess...).
Since I don't believe you can get them locally, if there any locals on here that want to try it out, send me a PM and I'll drop a pad, or two, in the mail for y'all. (unless I run out, I guess...).
One question for everyone, I just got my Heron today in the mail and I'm curious to know how do you tell the difference between the original and updated bell.
Sent from my SCH-I605 using Tapatalk
Sent from my SCH-I605 using Tapatalk
1. If you observe thru the bell's channel against light you are likely to see reduced shoulder mid way.
2. Peeps have gotten unnecessary gurgling and condensation spitfires from the previous bell -- I didn't.
The air tube on the new bell has a larger inner diameter. On the old bell you will be able to see a little ridge inside.
You guys are awesome and are kick ..., love the GP Family and being part of it.
Sent from my SCH-I605 using Tapatalk
Sent from my SCH-I605 using Tapatalk
Good evening GP fam!
Are we expecting to see the v3 Lux on this next vapor day? I have another really expensive collectible hobby and need to make sure I keep a savings to keep up lol
Are we expecting to see the v3 Lux on this next vapor day? I have another really expensive collectible hobby and need to make sure I keep a savings to keep up lol
Hope so, if not I'll settle for topcap and switch. Haven't heard officially that v3 lux will be next Vapourday (I don't think.)
Good evening GP fam!
Are we expecting to see the v3 Lux on this next vapor day? I have another really expensive collectible hobby and need to make sure I keep a savings to keep up lol
I bet we find out within the next 8 hours.
I bet we find out within the next 8 hours.
Does this mean VD is tomorrow?
Sent from a BIG phone.....Galaxy Note 3
No, but P said the store will re-open on May 6th and soon thereafter he will announce the next VapourDay.
Edit: "Within the next 8 hours" was my being optimistic about VD news. It may not happen until later in the week.
- Status
Similar threads
- Locked
- Sticky
- Locked
